I connected TM1 at CS. All turbo pumps have been started. The pumping down is  good so far.

The TM1 HS line is  pressure tested this morning with 70 psi helium  at CS. No response has been found on leak detector.

Stop TM1 and CS turbo pumps and ruff pump. TM1 is disconnect at CS. It will be vented tomorrow morning and moved to ITW.

  TM1 has been connected in ITW . The new roughing pump replaced on last Friday works good. I started all turbo pumps in ITW. The ITW TP1 controller was broken during the starting time. Dimo and I changed a new controller for ITW TP1 in electrical room. The pumping down is good so far. ITW water supplies to TM1 only.      

• TM2 installed in Conditioning Station
• Varian Leak detector connected directly to Target Module 2 Service cap.
• Vacuum draw in Target Station with both module turbo pumps
• Leak detector baseline normal (10^-4 Torr, 10^-9 Std cc/s He)
• Since no Source tray is installed, and tube heater supply conductor is blanked off in target enclosure, it was necessary to test both supply and return points.
• For each line tested, 80 psi He was connected, and waited ~2 min to for a response on the leak detector.
• Lines tested:
  • conductor D (tube heater), Supply -> no He response
  • conductor D (tube heater), Return -> no He response
  • conductor C (tube heater), Supply -> no He response
  • conductor C (tube heater), Return -> no He response
• Based on this leak testing, both supply and return lines of conductors C & D are leak tight under 95 psi He (80 psig He supply to vacuum)

I turned off TM2 and CS turbo-pumps. TM2 will be moved from CS to silo tomorrow morning.

ITE entrance module is reconnected in ITE.

Isaac and I leak checked TM4 HS line with new UCX target. The leak detector base LR 0.0xE-9 atm.cc/sec, base pressure0.0xE-4torr. Isaac sprayed helium  on both VCR connections(5 seconds each) and flushed helium around the target for 6 seconds. No response on leak detector.

TM4 is connected at CS. All turbo pumps are started. The pumping down is good so far.

Helium pressure test on TM4 HS water line at CS is finished. 80psi helium no leak. 

TM4 are vented with argon and disconnected at CS this morning.

TM4 is connected in ITE. All ITE  turbo pumps are started. I will check the pumping down process tomorrow morning. Everything is fine so far.

ITE TP4S was broken down last night . I stopped the ITE pumps and vented station with Argon this morning. Edi and I replaced the broken pump with a new pump. The ITE is under roughing now.

5 Shielding blocks have been transferred from ITW to ITE. ITE  is configured to take proton beam.
 

  TM1 has been disconnected in ITW.

Chad and I  leak checked the TM1 HS line with new target installed. Base leak rate 0.0xe-9 atm.cc/sec. No any response has been found on LD. The line will be pressurized at CS with helium tomorrow.

TM1 is connected in CS. All turbo pumps are started.

Helium pressure test on TM1 HS water line at CS is done. 80psi helium with LD 0.0xE-9 atm.cc/sec. 3 minutes test and no response on LD. The line is leak tight.

Stopped TM1 and CS turbo pumps. Disconnected TM1 at CS. The CS and TM1 are under vacuum and naturally leak up. I will vent it on Wednesday morning.

Removed ITW HS and COIL flow rate monitors installed at the beginning of this year. They were installed on these two circuits for testing.They are broken during last run in ITW due to radioactive field.