ELOG RH-ISAC

Logbooks Lab Maintenance Evaporator_1 Evaporator_2 Laser cutter Target Production Test-Stand RH-ISAC RH-Cyclotron RH-Meson Hall RH-Beamlines RH-ARIEL

RH-ISAC, Page 33 of 140

Not logged in

Back | Find | Select | Help | Login

Full | Summary | Threaded | Hide attachments

2792 Entries

Goto page Previous 1, 2, 3 ... 32, 33, 34 ... 138, 139, 140 Next

ID	Date	Author	Category	Type	Module	Target/Number	Subject
1429	Friday, January 27, 2017, 08:46	chad fisher	South Hot-Cell	Standard Operation	TM4	Ta#50	Ta#50 Removed
Ta#50 has been was removed from TM4 on Wednesday, January 25th.
1329	Wednesday, August 24, 2016, 09:17	chad fisher	South Hot-Cell	Standard Operation	TM2		Ta#49
Ta#49 has been installed on TM2 and tested. All high current fasteners torqued to 130 in lbs.
1273	Wednesday, July 06, 2016, 09:16	chad fisher	South Hot-Cell	Standard Operation	TM2	SiC#33	Ta#48 removed SiC#33 installed
Ta#48 has been removed from TM2 and SiC#33 installed.
1225	Tuesday, May 10, 2016, 13:37	chad fisher	South Hot-Cell	Standard Operation	TM2	Ta#48	Ta#48 Installation
Ta#48 has been installed onto TM2. Also new window gaskets were installed. High current fasteners were torqued to 130 in lbs. Shutter side of the containment box recieved new fasteners.
1132	Tuesday, November 24, 2015, 14:03	chad fisher	South Hot-Cell	Standard Operation	TM4		Ta#46
Ta#46 has been removed from TM4.
869	Tuesday, March 24, 2015, 09:47	chad fisher	South Hot-Cell	Standard Operation	TM4	Ta#45	Ta#45 installed
Ta#45 has been installed onto TM4 and is ready for leak and electrical check. High current fasteners torqued to 130 in.lbs.
867	Monday, March 23, 2015, 14:03	chad fisher	South Hot-Cell	Standard Operation		Ta#45	Ta#45 inserted into hot cell
Ta#45 has been inserted into the hot cell. Swipe taken of inner tool port area: 100000 counts/min.
878	Monday, March 30, 2015, 09:03	Anders Mjos	Conditioning Station	Standard Operation	TM4	Ta#45	Ta#45 Conditionoing
Monday, March 30, 2015, 08:59: Reset chiller by switching on off power (fault 2) Monday, March 30, 2015, 09:02: Switched on CHILL:CP2, TS5 at 34 C Monday, March 30, 2015, 10:24 : Cage locked. EE to GND. BIAS and EL ON. Troubleshooting BIAS current limiting. Turned out to be a EPICS initialization issue. Resolved by setting/changing the current limit again in EPICS. Monday, March 30, 2015, 14:00: BIAS/EL 18 / 9 kV Monday, March 30, 2015, 14:16: BIAS/EL 24 / 12 kV Monday, March 30, 2015, 16:03: BIAS/EL 30 / 15 kV. Occasional sparking while stepping up since 26 kV Monday, March 30, 2015, 16:13: BIAS/EL 30.8 / 15 kV. 110% of scheduled 28 kV. BIAS/EL 0.04 / 0.09 mA Monday, March 30, 2015, 17:26 : Maintained BIAS over 1 hour. One spark after. Monday, March 30, 2015, 17:27 : BIAS / EL off. Tuesday, March 31, 2015, 08:12: Cage access. EE to EE PS. Cage locked. Tuesday, March 31, 2015, 08:24: BIAS/EL/EE at 30.8 / 15 / 1 kV Tuesday, March 31, 2015, 08:26 : EE to 2 kV, 1.96 mA Tuesday, March 31, 2015, 08:46: No sparks for 20 min. Tuesday, March 31, 2015, 08:48 : BIAS/EL/EE at 20 / 9.3 / 1.5 kV Tuesday, March 31, 2015, 08:57: Started auto ramping of heaters to 580 / 230 A at 2 A/min. Tuesday, March 31, 2015, 10:54: TBHT at 230 A Tuesday, March 31, 2015, 14:05: TGHT at 580 A Tuesday, March 31, 2015, 14:21: BIAS/EL/EE to 30.8 / 15 / 2 kV Tuesday, March 31, 2015, 17:48: Source stable for 4h Tuesday, March 31, 2015, 18:20: Lowered IAS/EL/EE to 20 / 9.3 / 1.5 kV. IG2 at 6.2E-6 T Tuesday, March 31, 2015, 21:27: Starting ramp down at 15/12 A/min. IG2 at 6.8E-6 T Tuesday, March 31, 2015, 21:51: BIAS/EL/EE to zero and off. IG2 at 6.6E-6 T Tuesday, March 31, 2015, 22:17: TGHT and TBHT off Tuesday, March 31, 2015, 22:41: Turbos off. Tuesday, March 31, 2015, 22:42: Water off.
Attachment 1: Ta#45_Conditioning.docx
793	Wednesday, November 19, 2014, 08:49	chad fisher	South Hot-Cell	Standard Operation	TM4	UCx#11	Ta#44 Removed Ucx#11 Installed
Ta#44 has been removed from TM4 and UCx#11 has been installed and is ready for testing. New fasteners were installed for all mounting and current connections. High current fasteners were torqued to 130in lbs.
630	Tuesday, March 25, 2014, 09:11	chad fisher	South Hot-Cell	Standard Operation	TM4	Ta#42	Ta#42 install and "new" 9 pin
Ta#42 has been installed onto TM4. The "new" 9 pin connector was not an issue...attually went on better than any other previous one. Leaving the mounting screws loose on the target half allowed use of the manipulator to center the pins and insert them with ease.
Attachment 1: TM4_20140325_01.jpg

356	Wednesday, May 22, 2013, 14:11	chad fisher	South Hot-Cell	Standard Operation	TM4	Ta#40	Ta#40 installed
Ta#40 has been installed. Leak checking and high voltage tomorrow before the move.
285	Wednesday, April 03, 2013, 13:28	chad fisher	South Hot-Cell	Standard Operation	TM1	Ta#39	Ta#39 installed
Ta#39 has been installed onto TM1.
282	Tuesday, April 02, 2013, 10:07	chad fisher	South Hot-Cell	Standard Operation	TM1	Ta#39	Ta#39 inserted into hot cell
Ta#39 has been inserted into the hot cell in preparation for TM1 target change.
393	Wednesday, July 03, 2013, 08:43	chad fisher	South Hot-Cell	Standard Operation			Ta#39 Transfered to spent target storage vault

394	Wednesday, July 03, 2013, 08:44	chad fisher, Travis Cave	South Hot-Cell	Standard Operation			Ta#39 Transfered to spent target storage vault
Ta#39 has been transferred to spent target storage vault. Ta#39 was placed into pail #106 and placed into spot of 4C of the spent target vault. The pail measured 95.8mSv/hr upon removal from the hot cell. See attached PDF for details.
Attachment 1: Vault_Storage_July_3_2013.pdf

389	Thursday, June 27, 2013, 14:23	chad fisher	South Hot-Cell	Standard Operation	TM1	Ta#39	Ta#39 Autopsy performed
An autopsy of Ta#39 was performed yesterday and today. Ta#39 will be sent to the spent target storage vault on Tuesday.
29	Wednesday, September 28, 2011, 10:06	chad fisher	South Hot-Cell	Standard Operation	TM4	Ta#36	Ta#36 Removal
Ta#36 was removed from target module 4. The standard, unexplained, un-investegated, un-resolved "arc" were again present on "JP's connector", otherwise no apparent problems visible. Chad
1922	Thursday, May 16, 2019, 12:31	chad fisher	South Hot-Cell	Standard Operation	TM2	Ta#58	Ta #58 installed
Ta #58 has been installed onto TM2. All new silver plated high current fasteners. All torqued to 130 in lbs.
569	Wednesday, December 04, 2013, 13:57	chad fisher	South Hot-Cell	Standard Operation	TM4	Ta #47	Ta #47 Removed - broken bolt
Ta #47 has been removed from TM4. One containment box cover bolt would not come out. Upon attempted removal with the stud remover the bolt sheared...which is not uncommon...just hasn't happened in many years...CBB being stuck or shearing. Nine pin connector shows the typical "arcing" mark.
70	Thursday, January 12, 2012, 14:32	David Wang	ITE	Repair	TM4		TP2 on TM4 has been replaced
TP2 on TM4 has been replaced with a new turbo pump , I didnt reset the controller in electrical room.So this new pump start to run at 8083 hours on ITE TP2 controller. The new TP2 pump properly started. It works fine now.

Goto page Previous 1, 2, 3 ... 32, 33, 34 ... 138, 139, 140 Next

ELOG V2.9.2-2455