Attached are pre-removal pictures of NB#7 and the inside face of the containment box cover before cleaning.

TM#1 with Nb#7 has been moved from the west target station to the south hot cell move went well.

This week six targets and the two source trays were assayed and surveyed from the storage vault. see attached PDF for details.

The F-308 have been cleaned and serviced. There were three F-308's that came back with some contamination.#13, #15 and #19 were found to have contamination. They were decontaminated. All of the loose contamination was removed. There is still some fixed contamination. The levels of contamination are low enough to still be used for shipping spent targets. They have been moved to the north hot cell area and are ready for to be filled with spent targets. 

Bevan and I transferred five shielding blocks from ITW to ITE. ITE is ready for taking proton beam.

The NiO #1 spent target was placed into storage today. It is in pail number 01 (101 on Vault Status page) and located in slot 4A of the vault. It was 35.5 mSv/hr upon removal from the south hot cell. See attached PDF for vault details.

Yesterday TM#4 with UCx#5 was moved to the east target station from the conditioning station,  move went well.

TM4 heat shield helium pressure test and electrical check were done  at CS  last week. The results are good. NO leak had been found on heat shield circuit.The electrical check is also good.

TM4 was remote moved from the SCH to the TCS today. This was the first time the module was moved with the framework for the cage in place. The ion gauge on the service cap is closer to the cage than anticipated and as a result the pins for the gauge were sheared off. Discussion as to how to repair the gauge (both short term and long term needs to be had). We will try and rough down the TM tonight, it is not believed the vacuum will be affected.

NiO#1 was removed this morning.

UCx#5 was inserted into the hot cell around 1 pm, installed and leak checked and ready to go to the conditioning station 1:40pm

did have a little trouble with the 9 pin connector. It had to be lossened to get it to mate properly. It was le-tightened once the proper fit was achieved.

 TM4 with NiO#1 was moved from ITE to the SHC today. The move went well with no issues.

I disconnected TM4 in ITE this morning. The heat shield circuit has been purged with air.

Grant and I replaced the conditioning station broken  srcoll pump with a refurbished scroll pump which is supplied by vacuum group. The replaced pump is bagged and waiting for RPG further survey in target hall . The target hall is survey after the job, and everything is fine.

5 shielding blocks have been moved from ITE to ITW. ITW is configured to take proton beam now.

ITE MSP water circuit flow wheel was replaced yesterday due to poor performance.

TM 1 is in ITW now. All connections are done. The turbo pumps had been started this afternoon. The vacuum looks good so far. The water interlock check which related to TM1 are done. They are good. All TM1 water signals are visually checked and they are strong.  The rest interlock check ( MCR XT page) will be finished before shielding blocks moving. The MAA is locked and ITE is ready for proton beam.        

TM#1 with Nb#7 moved from the conditioning station to the west target station. Move went well.

Leak detector pumped down to base LR1.3xE-9 atm.cc/sec, and BP 8xE-3 torr. All high vacuum gauge readings at CS and TM1 are at low -6 range from 1.2xE-6torr to 4.6x E-6 torr. Applied 80 psi helium  to heat shield circuit for 5minutes and there is no any response on leak detector. The heat shield circuit is leak tight.

Electrical check was done at the conditioning station this morning results are on the attached PDF.

TM#1 with Nb#7 was moved from the south hot cell to the conditioning station. Move went well.