ELOG Target Production

Logbooks Lab Maintenance Evaporator_1 Evaporator_2 Laser cutter Target Production Test-Stand RH-ISAC RH-Cyclotron RH-Meson Hall RH-Beamlines RH-ARIEL

Target Production, Page 7 of 8

Not logged in

Back | Find | Select | Help | Login

Full | Summary | Threaded | Collapse | Expand

145 Entries

Goto page Previous 1, 2, 3 ... 6, 7, 8 Next All

Monday, October 07, 2024, 13:16, Aaron Schmidt, Ta#68, HP-SIS, ITE, TM2, 45447-26, 45235-16, Ready, Ta#68 Target Description

ITE-TM2-Ta#68-HP-SIS_Target_Loading_Data.pdf

Ta#68 HP-SIS target description:

Total Ta foils = 470 [6x20 packs + 350 single discs]

Foil Thickness = 0.0254mm (0.0010") avg Measured.

Target material batch: PO# TR-2023-06149

Target density = 14.204 g/cm3

Target length = 3.50 cm

Total Mass = 49.7146 g [Incl foils + Ta wire on 6 packs]

Total mass w/ Target oven = 1483g (w/ end caps)

Discs in target are arranged as follows: 1pack / 75 singles / 1pack / 100 singles / 2packs / 100 singles / 1pack / 75 singles / 1pack

Dimpling direction on foils/ Packs. --> Center <--

End caps installed (Expanded). No Ta foil heat shield added

Wednesday, July 10, 2013, 18:41, John Wong, SiC#29, HP-FEBIAD-CTL, ITE, TM4, 38481-6, 39956-4, Spent, SiC#29 - Target description

Wednesday, July 10, 2013, 18:32

SiC#29 HP-FEBIAD-CTL target description:

Total SiC foils = 510 discs

Total mass SiC + C_grv foils = 62 g (before sintering, expecting ~13% loss of organic mass after burnt off)

Average mass SiC/disc (without C_grv) = 0.0892 g

Average thickness SiC (without C_grv) = 0.21mm

No Rh foil and salt added for this run.

See attachment #1 for the density measurement.

Wednesday, July 10, 2013, 18:40

Target is currently in the Test-Stand. Once it's tested; it is ready to go online.

Happy Beaming!

Tuesday, May 30, 2017, 15:15, Laura Lambert, SiC#36, HP-FEBIAD-CTL, , TM2, 41369-10, , Ready, SiC#36 target description

Tuesday, May 30, 2017, 15:12

See attachment for target description.

Friday, September 23, 2011, 17:03, Anders Mjos, SiC#26, HP-FEBIAD, ITE, TM4, 38295-9, 38307-8, Spent, Run finished

Friday, September 23, 2011, 16:54:

Cu-gaskets used for leak checking target had a leak rate of about 10^-8 10^-9 atm cc/sec. Replaced with silver plated SS gaskets and no leak detected above 10^-11 atm cc/sec.
The target can not hold high voltage when it is sitting on the jig. The insulator on the jig have reduced resistance over time (less than 1 G Ohm). All high voltage tests passed when target is tested not sitting on the jig.

Target is now in the test stand and pumping down.

Monday, October 17, 2011, 14:45, John Wong, SiC#26, HP-FEBIAD, ITE, TM4, 38295-9, 38307-8, Spent, Run finished

Anders Mjos wrote:

Friday, September 23, 2011, 16:54:

Cu-gaskets used for leak checking target had a leak rate of about 10^-8 10^-9 atm cc/sec. Replaced with silver plated SS gaskets and no leak detected above 10^-11 atm cc/sec.

The target can not hold high voltage when it is sitting on the jig. The insulator on the jig have reduced resistance over time (less than 1 G Ohm). All high voltage tests passed when target is tested not sitting on the jig.

Target is now in the test stand and pumping down.

Monday, October 17, 2011, 14:41

After the test-stand, the extraction electrode showed some electric arcing mark, but no solid deposits were found. (see attachment#1: EE_after_teststand.jpg)

See attachment for the target specification.

Thursday, October 11, 2012, 11:41, John Wong, NiO#1, HP-FEBIAD, ITE, TM4, 38481-7, 39069-1/10(lid), Spent, NiO target description

(Should have posted this before my long vacation... Anyway, it's for documentation)

Thursday, October 11, 2012, 11:38

NiO/Ni #1	Average
NiO + Ni (g)	0.109
NiO - Ni foil (g)	0.06
NiO + Ni thickness (mm)	0.116
NiO - Ni Thickness (mm)	0.091
Area (cm2)	2.212
NiO + Ni - organics 8.95% (g)	0.099
NiO - Ni - Organics (g)	0.055
NiO Density (g/cm3)	2.145 (32%)

Target contains 500 NiO/Ni discs and is measured at 9.0 in length.

Tuesday, December 11, 2012, 15:44, Anders Mjos, SiC, HP-FEBIAD, ITW, TM4, na, na (old style fittings), Ready, Test target for the Conditioning Station

The target has been used for operator training previously at the ISAC Test Stand.

9-pin connector was completed and grounded
RH gripper arms added to the heat shield

Further documentation on DocuShare

Friday, August 30, 2013, 14:45, John Wong, NiO#2, HP-FEBIAD, , , 39530-6, 39069-4, Spent, NiO target description

Friday, August 30, 2013, 14:38

NiO/Ni#2 Average

NiO+ Ni (g) 0.114

NiO - Ni foil (g) 0.066

NiO + Ni thickness (mm) 0.116

NiO - Ni thickness (mm) 0.104

Area (cm2) 2.212

NiO + Ni - organics (8.95%) (g) 0.104

NiO - Ni - organics (8.95%) (g) 0.060

NiO Density (g/cm3) 2.110

% Yield density 32%

# discs in target 530

Total target length (cm) 9.0

Wednesday, April 30, 2014, 16:36, John Wong, SiC#30, HP-FEBIAD, ITE, TM3, 38481-8, , Spent, SiC#30 Target description

Wednesday, April 30, 2014, 15:16

Note:

This target was built in 2011. The endcaps were replaced after they got vaporized in Evap#1 during the sintering process, and the target was re-conditioned.

See elogs for more details:

https://elog.triumf.ca/TIS/Evaporator_1/20

The target was inspected and was good for online use.

Total SiC foils = 555 discs

Total length (packed) = 17.5cm

Total SiC mass (plus graphite foils) = 52.902g

See attachment for density measurements

Thursday, September 24, 2015, 13:42, Laura Lambert, SiC#32, HP-FEBIAD, , , 39530-5, , Ready, SiC#32 target description

Thursday, September 24, 2015, 11:46

See attachment for target description.

Friday, October 07, 2016, 16:27, John Wong, SiC#35, HP-FEBIAD, , , 39530-9, , Ready, SiC35 Target description

Friday, October 07, 2016, 16:28