The job is done. See attachment.

 TM#2 with Ta#55 has been moved from the west target station to the south hot cell.

Attached alignment check notes after brazing and fabrication.

First page lower half shows establishment of baseline using master jig

Second page top half shows the alignment of the target mounting plate jig and the steerer cone aperture.

Second page bottom half shows alignment of the master target jig. Master target jig needed the 9 pin and heat shield locating features removed to seat the target correctly.

Overall, source tray assembly sits .006" high on average (min .003", max .010"), .003" to the left with respect to ion beam axis.

TM#2 has been moved from the south hot cell to the conditioning station.

I did a helium pressure test on TM2 water lines at TCS. We will remove the TM2 source tray soon so this test is a reference check for future new source. The result:

Helium 70 psi, 2 minutes to each circiut. Leak detector  base LR.0.0x e-9atm.cc/sec, base pressure  0.0x e-4torr

Ta+(A)  0.0x e-9atm.cc/sec

Ta-(B)  0.0x e-9atm.cc/sec

Tu-(C) 7.8x e-7 atm.cc/sec

Tu+(D) 3.5x e-7 atm.cc/sec

Coil 2(PU) 0.0x e-9atm.cc/sec

Coil 1(RU) 0.0x e-9atm.cc/sec

EE 8.2 x e-9atm.cc/sec

MSP 0.0x e-9atm.cc/sec

Containment box window  0.0 xe-9atm.cc/sec

HS  no target and opened. No test.

All water lines on module side in TM2  should be in good condition according to this test . The leak response we found on B and C lines are from water block seals mostly.           

I switched off TM2 and TCS vacuum pumps. The TCS and TM2 will be under vacuum without pumping.

The containment box has been removed from TM2, the Enzel lens and steerers disconnected and optics tray removal has commenced.

 TM#2 has been moved from the conditioning station to the south hot cell.

Tm2 containment box has been re-installed onto TM2.

I have "slung" the TM4 optics tray in preparation for its removal.

 TM2 has been moved from the silo to the south hot cell.

On Thursday, June 29th the containment box of TM2 was removed and the optics tray re-installed and reconnected. The box was then re-installed.

Friday the window waterlines were leak checked, Nb target installed (with new fasteners, high current torqued to 130 in*lbs) target leak and electrical checked and containment box cover installed with new fasteners.

 The results of the various electrical checks performed on the TM#2 with and without the Nb#8 target attached.

 TM#2 with Nb#8 has been moved from the south hot cell to the west target station.

TM2 has been connected to ITW. All turbo pumps are started. See attachment for connection checklist.

Maico and Travis moved blocks from ITE to ITW yesterday

The 2A2M19 beam profile monitor did not work and was e-faulted. After initial troubleshooting 2 blocks were removed form ITW to inspect the entrance module where the beam monitor is installed. The cable was found not to be connected and was quickly fixed. Blocks reinstalled. The work was done by Maico, Travis and Anders

ITW Entrance Module was leak checked yesterday with the support of Vacuum Group (Dimo & Edi). The leak detector was connected to primary backing vacuum line. A leak response was found near the bellow for the beam profile monitor on top of the Entrance Module. It could be confirmed today by actuating the monitor, that the leak was indeed at that location. The plan is to move the TM and Entrance Module out for target exchange and repair, respectively. Drawings of the device available on ITA0200and ITA5128

 TM#2 with Nb#8 has been moved from ITW to the south hot cell.

 TM#2 with UC#23 has been moved from the south hot cell to the conditioning station.