Monday, March 10, 2014, 11:44

Rick replaced the backing pump hose from 1.5" to 2.0" for better flow.  And the HEPA filter was checked - it looks OK.

Friday, January 11, 2013, 10:59

The insulator that holds the terminals was broken when a target container was installed.  The insulator had seen so much heat shine from the Cu heat-shield gaps, see attachment.  Tightening the bolts on the target container might further put more force on the insulator and eventually broke it.

To prevent this to happen again.  The Cu-heat shield gaps have covered with Ta-foil to prevent any shine from the target  container onto the insulator.  Also, a torque wrench will be used to tighten the bolts on the terminals.  At this point, we don't know the max torque the insulator can tolerate.  Some measurements were done on the target resistant (ohm) as a function of torque (in pounds).  The best torque to tighten the terminal bolts is 150 lbs. 

John Wong wrote:

Friday, January 11, 2013, 10:59 The insulator that holds the terminals was broken when a target container was installed.  The insulator had seen so much heat shine from the Cu heat-shield gaps, see attachment.  Tightening the bolts on the target container might further put more force on the insulator and eventually broke it. To prevent this to happen again.  The Cu-heat shield gaps have covered with Ta-foil to prevent any shine from the target  container onto the insulator.  Also, a torque wrench will be used to tighten the bolts on the terminals.  At this point, we don't know the max torque the insulator can tolerate.  Some measurements were done on the target resistant (ohm) as a function of torque (in pounds).  The best torque to tighten the terminal bolts is 150 lbs.

The insulators were installed with torques as indicated in the attached PDF ITD0052. A torque test was performed on the broken insulator before installation. No damage was seen on torques of up to 60 in lbs for the 1/4-20 bolts, however for torques in excess of 50 in lbs the insulator material seems to "give".

 Tuesday, April 16, 2019, 13:38: Replaced the bottom insert on the heat shield. 

Used small amount of isopropyl alcohol to wipe the inside if the HS out. 

Wednesday, May 29, 2024, 22:52

Small graphite cartridge was loaded with SiC discs 240523-1 and 240523-2 and 220727-2 (baseline discs).  Test Discs produced without milling using PAA as a dispersant.

The coated container tube was wrapped in four Ta foil heatshields.

two Tac Coated springs at the ends in case plugs are pushed outwards.

Target temperature on OMEGA= 1850-1900 C

OMEGA slope:= 0.990

Target time at max temperature = 4 hours

Final TGHT current= ~400A (adjustable)

Heating autoramp 2A/min to 90 A

Then at 2A/min to 120A.

Good vacuum = 5.0 e-02 Torr

Bad vacuum = 5.0E-04 Torr

 IGP1 initial 4.8e-07 Torr

Wednesday, May 29, 2024, 22:54

Kept at 400 A for 4 hours. 

Starting autoramp down at -2A/min

John Wong wrote:

Laura Lambert wrote: John Wong wrote: Tuesday, September 01, 2015, 17:16 Target container contains 533 discs of SiC with packed length of 17cm.  Mass of 533 discs SiC(green)  = 57.8979g Total mass SiC(green) + target container = 1455g Container is wrapped with 3 heatshields; no end caps are inserted yet. Sintering temp at 1800C - TGHT will be set accordingly.  TBHT max at 230A.  Chamber is currently being pumped down.     Wednesday, September 02, 2015, 09:11 HS water valves opened, no leaks detected. IGP1 = 1.15e-6 Torr Tapped up manually to 40A. Waited ~1hr40 for vacuum to stabilize. IGP1 = 3.6e-6 Torr. Max setpoints set to TGHT = 630A and TBHT = 230A, ~1400C Initiating auto ramp at a rate of 0.2A/min and 0.1A/min for the TGHT and TBHT respectively. Once max setpoints achieved, will tap up manually until window port becomes coated [as previously observed] Once window port becomes coated will leave at set temp for ~4hrs to continue with outgassing, then cool down, clean window and ramp back up. If LS port still clean, will continue to ramp up to final desired temperature of 1800C.  Wednesday, September 02, 2015, 14:23 IGP1 = 4.0e-5 Torr. Vacuum too high, stopped auto-ramp and tapped down manually. Dropped TGHT down from 80A to 50A Dropped TBHT down from 55A to 50A Wednesday, September 02, 2015, 15:29 Vacuum down to IGP1 = 1.2e-5 Torr. Re-initiating auto-ramp...  Tuesday, September 08, 2015, 10:04 IGP1 = 4.5e-7 Torr. TGHT = 630A, 9.6V TBHT = 230A, 3.2V DV = 0.22V OMEGA RS = 1476C OMEGA LS = 1450C see attached photo for screenshot. will tap up manually with a visual on both window ports...    Tuesday, September 08, 2015, 15:44 TGHT has stepped up to 820A.  Coating on both windows is becoming obvious and it's interfering the temp readers; however, the left window (see attachment, which is further away from the target) is lightly coated than the right.  See attachment for The Temp (and Power) vs current plots. Target will remained heated at the current and will be cooled down later today.    The target will be re-conditioned up to 820A and temp and mass will be re-measured. Plans: The chamber will be vented tomorrow and the target will be taken out to weigh for mass change.  The chamber windows will need to be clean. A piece of Ta foil will be cover in front of the ionizer to trap any loss material (if any).  Tuesday, September 08, 2015, 17:37 TGHT was at 800A for 2 hours before ramping up 820A for another 2 hours heating.  More coating on the right window is observed and temp reading came down to 1340C.  The left window remains the same and temp reads at 1646C.   Ramping TGHT/TBHT to 0A at 2A/min and 1A/min, respectively.    Wednesday, September 09, 2015, 12:27 Result after the sintering process: No yellow crystal formed (compared to previously observed SiC targets that heated up above 1900C).  Total green mass = 57.90g  mass of graphite foil = 0.035g x 533 discs = 18.7g  mass of green SiC = 39.30g  Target container with SiC before sintered = 1455g  Target container after sintered = 1450g  mass loss ~ 5.0g ~ 13% organic mass, as expected!   The target will undergo the re-condition stage, and the temperature will be measured from 600A to 820A.

 Wednesday, September 09, 2015, 17:39

Both end-caps are inserted onto the targets.  The total mass (Target, Sintered SiC, end caps, 4x 19"round graphite foils) = 1453g.

Target is wrapped with 3 layers of heat shields.  

The extraction electrode is wrapped with Ta-foil (see attachment).  This is to trap any lose particle, if any.  

Chamber is currently being pumped down, currently at 1.2e-5 Torr.  

John Wong wrote:

John Wong wrote: Laura Lambert wrote: John Wong wrote: Tuesday, September 01, 2015, 17:16 Target container contains 533 discs of SiC with packed length of 17cm.  Mass of 533 discs SiC(green)  = 57.8979g Total mass SiC(green) + target container = 1455g Container is wrapped with 3 heatshields; no end caps are inserted yet. Sintering temp at 1800C - TGHT will be set accordingly.  TBHT max at 230A.  Chamber is currently being pumped down.     Wednesday, September 02, 2015, 09:11 HS water valves opened, no leaks detected. IGP1 = 1.15e-6 Torr Tapped up manually to 40A. Waited ~1hr40 for vacuum to stabilize. IGP1 = 3.6e-6 Torr. Max setpoints set to TGHT = 630A and TBHT = 230A, ~1400C Initiating auto ramp at a rate of 0.2A/min and 0.1A/min for the TGHT and TBHT respectively. Once max setpoints achieved, will tap up manually until window port becomes coated [as previously observed] Once window port becomes coated will leave at set temp for ~4hrs to continue with outgassing, then cool down, clean window and ramp back up. If LS port still clean, will continue to ramp up to final desired temperature of 1800C.  Wednesday, September 02, 2015, 14:23 IGP1 = 4.0e-5 Torr. Vacuum too high, stopped auto-ramp and tapped down manually. Dropped TGHT down from 80A to 50A Dropped TBHT down from 55A to 50A Wednesday, September 02, 2015, 15:29 Vacuum down to IGP1 = 1.2e-5 Torr. Re-initiating auto-ramp...  Tuesday, September 08, 2015, 10:04 IGP1 = 4.5e-7 Torr. TGHT = 630A, 9.6V TBHT = 230A, 3.2V DV = 0.22V OMEGA RS = 1476C OMEGA LS = 1450C see attached photo for screenshot. will tap up manually with a visual on both window ports...    Tuesday, September 08, 2015, 15:44 TGHT has stepped up to 820A.  Coating on both windows is becoming obvious and it's interfering the temp readers; however, the left window (see attachment, which is further away from the target) is lightly coated than the right.  See attachment for The Temp (and Power) vs current plots. Target will remained heated at the current and will be cooled down later today.    The target will be re-conditioned up to 820A and temp and mass will be re-measured. Plans: The chamber will be vented tomorrow and the target will be taken out to weigh for mass change.  The chamber windows will need to be clean. A piece of Ta foil will be cover in front of the ionizer to trap any loss material (if any).  Tuesday, September 08, 2015, 17:37 TGHT was at 800A for 2 hours before ramping up 820A for another 2 hours heating.  More coating on the right window is observed and temp reading came down to 1340C.  The left window remains the same and temp reads at 1646C.   Ramping TGHT/TBHT to 0A at 2A/min and 1A/min, respectively.    Wednesday, September 09, 2015, 12:27 Result after the sintering process: No yellow crystal formed (compared to previously observed SiC targets that heated up above 1900C).  Total green mass = 57.90g  mass of graphite foil = 0.035g x 533 discs = 18.7g  mass of green SiC = 39.30g  Target container with SiC before sintered = 1455g  Target container after sintered = 1450g  mass loss ~ 5.0g ~ 13% organic mass, as expected!   The target will undergo the re-condition stage, and the temperature will be measured from 600A to 820A.     Wednesday, September 09, 2015, 17:39 Both end-caps are inserted onto the targets.  The total mass (Target, Sintered SiC, end caps, 4x 19"round graphite foils) = 1453g. Target is wrapped with 3 layers of heat shields.   The extraction electrode is wrapped with Ta-foil (see attachment).  This is to trap any lose particle, if any.   Chamber is currently being pumped down, currently at 1.2e-5 Torr.

 Thursday, September 10, 2015, 09:55

HS water valves opened this morning, no leaks detected.

TGHT and TBHT tapped up manually to 35A.

IGP1 = 4.4e-7 Torr, vacuum stable.

Initiating auto-ramp at 1.0A/min and 0.5A/min for the TGHT and TBHT respectively with final setpoints of 600A and 230A.

Laura Lambert wrote:

John Wong wrote: John Wong wrote: Laura Lambert wrote: John Wong wrote: Tuesday, September 01, 2015, 17:16 Target container contains 533 discs of SiC with packed length of 17cm.  Mass of 533 discs SiC(green)  = 57.8979g Total mass SiC(green) + target container = 1455g Container is wrapped with 3 heatshields; no end caps are inserted yet. Sintering temp at 1800C - TGHT will be set accordingly.  TBHT max at 230A.  Chamber is currently being pumped down.     Wednesday, September 02, 2015, 09:11 HS water valves opened, no leaks detected. IGP1 = 1.15e-6 Torr Tapped up manually to 40A. Waited ~1hr40 for vacuum to stabilize. IGP1 = 3.6e-6 Torr. Max setpoints set to TGHT = 630A and TBHT = 230A, ~1400C Initiating auto ramp at a rate of 0.2A/min and 0.1A/min for the TGHT and TBHT respectively. Once max setpoints achieved, will tap up manually until window port becomes coated [as previously observed] Once window port becomes coated will leave at set temp for ~4hrs to continue with outgassing, then cool down, clean window and ramp back up. If LS port still clean, will continue to ramp up to final desired temperature of 1800C.  Wednesday, September 02, 2015, 14:23 IGP1 = 4.0e-5 Torr. Vacuum too high, stopped auto-ramp and tapped down manually. Dropped TGHT down from 80A to 50A Dropped TBHT down from 55A to 50A Wednesday, September 02, 2015, 15:29 Vacuum down to IGP1 = 1.2e-5 Torr. Re-initiating auto-ramp...  Tuesday, September 08, 2015, 10:04 IGP1 = 4.5e-7 Torr. TGHT = 630A, 9.6V TBHT = 230A, 3.2V DV = 0.22V OMEGA RS = 1476C OMEGA LS = 1450C see attached photo for screenshot. will tap up manually with a visual on both window ports...    Tuesday, September 08, 2015, 15:44 TGHT has stepped up to 820A.  Coating on both windows is becoming obvious and it's interfering the temp readers; however, the left window (see attachment, which is further away from the target) is lightly coated than the right.  See attachment for The Temp (and Power) vs current plots. Target will remained heated at the current and will be cooled down later today.    The target will be re-conditioned up to 820A and temp and mass will be re-measured. Plans: The chamber will be vented tomorrow and the target will be taken out to weigh for mass change.  The chamber windows will need to be clean. A piece of Ta foil will be cover in front of the ionizer to trap any loss material (if any).  Tuesday, September 08, 2015, 17:37 TGHT was at 800A for 2 hours before ramping up 820A for another 2 hours heating.  More coating on the right window is observed and temp reading came down to 1340C.  The left window remains the same and temp reads at 1646C.   Ramping TGHT/TBHT to 0A at 2A/min and 1A/min, respectively.    Wednesday, September 09, 2015, 12:27 Result after the sintering process: No yellow crystal formed (compared to previously observed SiC targets that heated up above 1900C).  Total green mass = 57.90g  mass of graphite foil = 0.035g x 533 discs = 18.7g  mass of green SiC = 39.30g  Target container with SiC before sintered = 1455g  Target container after sintered = 1450g  mass loss ~ 5.0g ~ 13% organic mass, as expected!   The target will undergo the re-condition stage, and the temperature will be measured from 600A to 820A.     Wednesday, September 09, 2015, 17:39 Both end-caps are inserted onto the targets.  The total mass (Target, Sintered SiC, end caps, 4x 19"round graphite foils) = 1453g. Target is wrapped with 3 layers of heat shields.   The extraction electrode is wrapped with Ta-foil (see attachment).  This is to trap any lose particle, if any.   Chamber is currently being pumped down, currently at 1.2e-5 Torr.      Thursday, September 10, 2015, 09:55 HS water valves opened this morning, no leaks detected. TGHT and TBHT tapped up manually to 35A. IGP1 = 4.4e-7 Torr, vacuum stable. Initiating auto-ramp at 1.0A/min and 0.5A/min for the TGHT and TBHT respectively with final setpoints of 600A and 230A.

Thursday, September 10, 2015, 12:05  

Changed TGHT to 2A/min and TGHT remains at 1A/min.  Vacuum is table at 1.0e-6 Torr. 

Friday, September 11, 2015, 11:34  

TGHT was at 600A for almost 20 hours.  Vac at 5.2 e-7 Torr.   L-temp at 1490C, R-temp at 1685 (odd?).   Using pyrometer to measure - Right end does seem brighter than the L end.  

Continue to ramp up TGHT.  Date is collected, will be posted later.  

 Friday, September 11, 2015, 11:53

L/R-temp measurements just don't seem normal.  

Ramped up to 220A- temp reads L = 1522C, R = 1722C.  

Ramping down TBHT doesn't change the temp.  

Will cool TGHT/TBHT to 0A at 2A/min & 1A/min, respectively.  

Will vent the chamber on Monday and inspect for any wrong.

 Monday, September 14, 2015, 12:13

The target has taken out for inspection.  No visible damage/problem was observed.  The Ta-foil for loss particle capture only showed some heat marking but no material was trapped. 

Target was weighted, no mass loss was observed.

Try expending the end caps to get a good thermal conductivity and will re-conditiong again.  

 Tuesday, September 15, 2015, 12:31

The end caps have been expended. 

New Ta foils are used for the heat shields.  The foils are cut in 3 1/4" x 12" and wrapped around the target.  (see attachment).  This is to see if the heat is evenly distributed.  

Both omega optical lens are aligned properly.  

Target is installed but the chamber is NOT yet being pumped down.  Awaiting for the fume hood work in B2 level to be complete before the evaporator can be started. 

 Wednesday, September 16, 2015, 17:57

The work in the B2 level is done; the nuclear ventilation for the evaporators is now operational. 

Chamber is currently being pumped down.

 Thursday, September 17, 2015, 12:19

Chamber has been pump down overnight and pressure is currently at 5.8e-7 Torr.

HS valves are opened and no leaks are detected.

Ramping up TGHT/TBHT to 600A at 2A/min and 230A at 1A/min, respectively.

 Thursday, September 17, 2015, 17:58

TGHT has reached to 600A/9.14V.  Both the L and R temperatures are measured at 1710C and 1760C, respectively.  At 600A, the temperature now is about 300C higher compared to that during the sintering process. 

The difference in the temperature could be from Ta surface vs SiC surface.  (But the 2-color IR temp reader shouldn't matter what color it's measuring?!! I don't know!)

Note: 

Both temperature readings are fairly close.  Could this be improved from the new Ta-foils?  Possible!

It is still unclear what is the absolute temperature.  A more systematic student needs to be done. 

Using a thermocouple couple to measurement the endcaps at 600A and compared with the Omage reader may help to understand more. 

After discussing with Friedhelm, it is decided to stay the target at 600A for the conditioning process. 

 Friday, September 18, 2015, 09:10

Target has been heated at 600A at stable temperature at 1716C (LS) and 1769C (RS), see attachment. 

 Friday, September 18, 2015, 11:45

Initiated cooling down at 2A/min for TGHT, and 1A/min TBHT. 

Currently vac at 5.48e-7 Torr.

 Thursday, September 24, 2015, 11:31

Target was inspected after the 2nd conditioning, up to 1700C at 600A for overnight. 

No solid particle was observed that might have extracted from the ionizer tube.  

The heat shields have been removed and the target is ready for assembly. 

Nikita Bernier wrote:

John Wong wrote: Nikita Bernier wrote: John Wong wrote: Tuesday, May 15, 2012, 12:24 The HP-SIS SiC target was made on Nov 03, 2010.  The target consists of 405 discs, 18.5cm in length.  It was sintered in the Evaporator#1.  This target is going into Evap#2 for re-conditioning.  It is currently being pumped down.    Friday, May 18, 2012, 12:19  The target is wrapped with only one heat shield. Evaporator #2 Target Heater is now auto-ramping at 0.5 A/min, up to 820 A, with the maximum voltage limited at 2 V, between 2.00e-05 (Good vacuum) and 3.00e-05 Torr (Bad vacuum). Tube Heater is auto-ramping at 0.5 A/min, up to 230 A, with the maximum voltage limited at 1 V. See attachments.  Friday, May 18, 2012, 13:15 Increased TBHT voltage to 5V, and TGHT to 15V.  Currently, TBHT =83A, 0.986V, TGHT= 144A, 1.65V, IGP1 = 5.2e-7 Torr, IGP2 = 4.3e-7 Torr.  Continue ramping up...   Tuesday, May 22, 2012, 12:02 TGHT and TBHT were ramped up to 830A/13.65V (local), and 235A/3.85V, respectively.  The target was conditioned over the long weekend.      Tuesday, May 22, 2012, 12:13 Initiating the cool-down process at 5 A/min. See archive plots of the Target Heater (Attachment 1) and the Tube Heater (Attachment 2).

 Tuesday, May 22, 2012, 15:24

TGHT/TBHT were ramped down to 0A.  The target has cooled for about 45 min.  All pumps and chillers are off.  The chamber has been vented.

Tuesday, May 15, 2012, 12:24

The HP-SIS SiC target was made on Nov 03, 2010.  The target consists of 405 discs, 18.5cm in length.  It was sintered in the Evaporator#1. 

This target is going into Evap#2 for re-conditioning.  It is currently being pumped down. 

John Wong wrote:

Tuesday, May 15, 2012, 12:24 The HP-SIS SiC target was made on Nov 03, 2010.  The target consists of 405 discs, 18.5cm in length.  It was sintered in the Evaporator#1.  This target is going into Evap#2 for re-conditioning.  It is currently being pumped down.

Friday, May 18, 2012, 12:19 

The target is wrapped with only one heat shield.

Evaporator #2 Target Heater is now auto-ramping at 0.5 A/min, up to 820 A, with the maximum voltage limited at 2 V, between 2.00e-05 (Good vacuum) and 3.00e-05 Torr (Bad vacuum). Tube Heater is auto-ramping at 0.5 A/min, up to 230 A, with the maximum voltage limited at 1 V. See attachments.

Nikita Bernier wrote:

John Wong wrote: Tuesday, May 15, 2012, 12:24 The HP-SIS SiC target was made on Nov 03, 2010.  The target consists of 405 discs, 18.5cm in length.  It was sintered in the Evaporator#1.  This target is going into Evap#2 for re-conditioning.  It is currently being pumped down.    Friday, May 18, 2012, 12:19  The target is wrapped with only one heat shield. Evaporator #2 Target Heater is now auto-ramping at 0.5 A/min, up to 820 A, with the maximum voltage limited at 2 V, between 2.00e-05 (Good vacuum) and 3.00e-05 Torr (Bad vacuum). Tube Heater is auto-ramping at 0.5 A/min, up to 230 A, with the maximum voltage limited at 1 V. See attachments.

 Friday, May 18, 2012, 13:15

Increased TBHT voltage to 5V, and TGHT to 15V.  Currently, TBHT =83A, 0.986V, TGHT= 144A, 1.65V, IGP1 = 5.2e-7 Torr, IGP2 = 4.3e-7 Torr. 

Continue ramping up... 

 Tuesday, May 22, 2012, 12:02

TGHT and TBHT were ramped up to 830A/13.65V (local), and 235A/3.85V, respectively.  The target was conditioned over the long weekend.  

John Wong wrote:

Nikita Bernier wrote: John Wong wrote: Tuesday, May 15, 2012, 12:24 The HP-SIS SiC target was made on Nov 03, 2010.  The target consists of 405 discs, 18.5cm in length.  It was sintered in the Evaporator#1.  This target is going into Evap#2 for re-conditioning.  It is currently being pumped down.    Friday, May 18, 2012, 12:19  The target is wrapped with only one heat shield. Evaporator #2 Target Heater is now auto-ramping at 0.5 A/min, up to 820 A, with the maximum voltage limited at 2 V, between 2.00e-05 (Good vacuum) and 3.00e-05 Torr (Bad vacuum). Tube Heater is auto-ramping at 0.5 A/min, up to 230 A, with the maximum voltage limited at 1 V. See attachments.  Friday, May 18, 2012, 13:15 Increased TBHT voltage to 5V, and TGHT to 15V.  Currently, TBHT =83A, 0.986V, TGHT= 144A, 1.65V, IGP1 = 5.2e-7 Torr, IGP2 = 4.3e-7 Torr.  Continue ramping up...   Tuesday, May 22, 2012, 12:02 TGHT and TBHT were ramped up to 830A/13.65V (local), and 235A/3.85V, respectively.  The target was conditioned over the long weekend.

 Tuesday, May 22, 2012, 12:13

Initiating the cool-down process at 5 A/min.

See archive plots of the Target Heater (Attachment 1) and the Tube Heater (Attachment 2).

Objective: Coating the inner surface of a short tantalum boat with rhenium.

Result:

• The wire snnaped around 376 W (53 A, and 7.09 V) and 2170 °C (measured with filament pyrometer)
• The tube does not have indications of coating

Thursday, March 25, 2021, 11:23

Yesterday a heat shield was installed in the EVAP2.

The desired temperature of the Re wire is 2500 degC

A water leak was performed (elog 539 describes it), no leak was detected.

Tuesday, March 23, 2021, 11:01

Pressure 3.8e-7 Torr, current rate set to 6 A @ 0.5 A/min

The wire started glowing at TGHT =  4W, 7A, 0.56V

When reaching 7A the current was increased 0.5 A manually 

When reaching 16 A,  the current was increased 1 A manually until reaching 54 A when the wire snapped

Objective: Coating the inner surface of a short tantalum tube with rhenium.

Result:

• The wire snnaped around 376 W (53 A, and 7.09 V) and 2170 °C (measured with filament pyrometer)
• The tube is coated

Thursday, March 25, 2021, 11:23

Yesterday a heat shield was installed in the EVAP2.

The desired temperature of the Re wire is 2500 degC

A water leak was performed (elog 539 describes it), no leak was detected.

Tuesday, March 23, 2021, 11:01

Pressure 3.8e-7 Torr, current rate set to 6 A @ 0.5 A/min

The wire started glowing at TGHT =  4W, 7A, 0.56V

When reaching 7A the current was increased 0.5 A manually 

When reaching 16 A,  the current was increased 1 A manually until reaching 54 A when the wire snapped

 Tuesday, April 13, 2021, 09:51

IGP1 = 2.5e-7 Torr

Tuesday, April 13, 2021, 10:17 

The wire was heated in the same manner as the last three runs

From 0A to 7A the autoramp was set to 0.5A/min

At 8A the wire started the glow dimmly 

Above 8A, the wire was heated manually at 0.5A until 15A where the step was changed to 1A, 

the temperature was measured with the filament pyrometer every 2 A starting at 10A

At 42 A the step was changed to 0.5A until 44.5A, 4.61V (2120 °C), the wire was kept at that temperature for 6 hours.

After that time, the current was ramped to 0A at 0.5A/min.

Objective: Coating the inner surface of a tantalum tube to make a destructive test and use a reference for the tantalum boats coatings

Results: The tube was coated

Sunday, March 28, 2021, 11:23

No water leak

IGP1 = 2.3e-7 torr

Sunday, March 28, 2021, 16:10

The wire was heated in the same manner as the last three runs

From 0A to 7A the autoramp was set to 0.5A/min

At 8A the wire started the glow dimmly 

Above 8A, the wire was heated manually at 0.5A until 16A where the step was changed to 1A, 

the temperature was measured with the filament pyrometer every 2 A starting at 10A

At 42 A the step was changed to 0.6A until 42.6A, 4.38V (2020 °C), the wire was kept at that temperature for 90 min

After that time, the current was ramped down at 0.5A/min until ~20A when the current rampping was changed too 1A/min

Objective: Coating the inner surface of a tantalum tube to make a destructive test and use a reference for the tantalum boats coatings

Results: 

Sunday, March 27, 2021, 11:23

No water leak

IGP1 = 3.7e-7 torr

Sunday, March 27, 2021, 16:10

The wire was heated in the same manner as the last three runs

From 0A to 7A the autoramp was set to 0.5A/min

At 8A the wire started the glow dimmly 

Above 8A, the wire was heated manually at 0.5A until 16A where the step was changed to 1A, 

the temperature was measured with the filament pyrometer every 2 A starting at 10A

At 42 A the step was changed to 0.6A until 42.6A, 4.38V (2020 °C), the wire was kept at that temperature for 90 min

After that time, the current was ramped down at 0.5A/min until ~20A when the current rampping was changed too 1A/min

Friday, March 26, 2021, 13:55

Yesterday a heat shield was installed in the EVAP2.

A 1mm thick rhenium wire was held within two copper brackets to pass through a Cu tube with the intention of coating its inside face.

The desired temperature of the Re wire is 2500 degC

A water leak was performed and no leak was detected

Laura Lambert wrote:

John Wong wrote: Laura Lambert wrote:  Tuesday, June 09, 2015, 9:16 Target container is coated with TaC. No Ta-heat shields are used. TGHT will be ramped up to 580A at 0.2A/min. TBHT will be ramped up to 230A at 01A/min. Chamber is currently being pumped down.  Tuesday, June 09, 2015, 15:37 HS water valves were opened. no leaks detected. Tapped up manually to 35A. Once vacuum stabilized after ~45min, initiated auto-ramp.  Wednesday, June 10, 2015, 08:02 IGP1 = 5.3e-7 Torr. TGHT = 250A and TBHT = 140A. Increasing auto ramp to 2.0A/min and 1.0A/min for the TGHT and TBHT respectively.    Wednesday, June 10, 2015, 16:32 TGHT/TBHT are at 580A/230A for almost 6 hours, temp at 1728C. Vac at 8.5e-7 Torr.  Cooling down initiated at 1A/min. Target container should be inspected once the chamber is vented.    Thursday, June 11, 2015, 10:55 Vented in air and opened up this morning. Same as last container sintered in evap2 [IG-LIS for UCx#13] - ends not quite fully sintered and coating not very good. most likely due to old TaC spray. See link for photos. https://www.dropbox.com/sh/75o43x8y2z16e7j/AABc8Z1fTTaTRtJ5_Jr1eacWa?dl=0

 Monday, June 15, 2015, 15:24

Same problem also found for the LP-IG-LIS container, WO#40860-1, see elog id#215.  After re-coating and sintering, it seems better. 

For this container, it is re-coated and will undergo the sintering process one more time. 

Will try to go up to 1900C for the sintering process.

Target container is temporarily wrapped with 6.2cm of Ta foil as a layer for heat shield on each side of the tube, excluding the centre block.  The shield will be removed once the process is done.  

Target current will be controlled accordingly. 

Chamber is being pumped down. 

 Monday, June 15, 2015, 16:17

HS water valves open; no leaks detected. 

IGP1 at 6.8e-6 Torr and coming down.

 Monday, June 15, 2015, 17:21

Stepping up TGHT/TBHT to 60A, pressure seems pretty stable at 7.2e-6 Torr and coming down. 

Setting TGHT to 400A and TBHT to 230A, auto-ramping initiated.   Will setup up current to reach 1900C, if necessary. 

 Monday, June 15, 2015, 20:28

TGHT and TBHT reached 400A/230A, Temp at 1552C.  Vac at 2.7e-6 Torr.

Stepping TGHT

Monday, June 15, 2015, 21:16  

TGHT at 520A/9.06 V to achieve 1900C.  DV at 5.09V.  

Vac at 4.2e-6 Torr.  

Will continue the sintering process at this temperature for another 3-4 hours. 

 Tuesday, June 16, 2015, 00:15

Target container has been heated at 1900C for over 3 hours.  

Vacuum is coming down to 1.4e-6 Torr.  

Initiated cooling process at 2A/min

Chamber can be vented tomorrow and container should be inspected

 Friday, June 26, 2015, 16:04

Container looks good!