Laura Lambert wrote:

Wednesday, April 05, 2017, 15:36 Coated container with TaC coating using spray technique this morning and let dry. Wrapped with one long layer of Ta heat shield, wrapped around boat 3x No ends to target boat Installed in evap2 and pumping down now...

 Thursday, April 06, 2017, 08:56

Problems with IGP2

Won't turn on, has low voltage output.

See screenshot attached.

Laura Lambert wrote:

Laura Lambert wrote:  Wednesday, April 05, 2017, 15:36 Coated container with TaC coating using spray technique this morning and let dry. Wrapped with one long layer of Ta heat shield, wrapped around boat 3x No ends to target boat Installed in evap2 and pumping down now...    Thursday, April 06, 2017, 08:56 Problems with IGP2 Won't turn on, has low voltage output. See screenshot attached.

 Thursday, April 06, 2017, 11:12

Turns out it was just a bad connection.

See attached photos.

Laura Lambert wrote:

Laura Lambert wrote: Laura Lambert wrote:  Wednesday, April 05, 2017, 15:36 Coated container with TaC coating using spray technique this morning and let dry. Wrapped with one long layer of Ta heat shield, wrapped around boat 3x No ends to target boat Installed in evap2 and pumping down now...    Thursday, April 06, 2017, 08:56 Problems with IGP2 Won't turn on, has low voltage output. See screenshot attached.    Thursday, April 06, 2017, 11:12 Turns out it was just a bad connection. See attached photos.

Thursday, April 06, 2017, 13:16

HS water valves opened, no leaks detected.

Tapped up manually to 35A

Waited almost 2hrs

IGP1 = 9.9e-7 Torr

Initiating auto-ramp at 0.2A/min to 400A

Final desired temperature = 1900C

OMEGA slope = 0.98

Good vac at 3.0e-5, bad vac at 4.0e-5 Torr.

 Monday, April 10, 2017, 09:26

IGP1 = 1.79e-7 Torr

TGHT = 400A, 6.47V

OMEGA = 1505C

Tapping up manually to 1900C...

 Monday, April 10, 2017, 11:46

TGHT tripped off at 410A, ~1530C

Water is still on and good flow.

Vacuum was stable ~1.8e-7 Torr.

No power trips according to controls.

Not sure of reasoning behind trip.

Initially tried tapping back-up, no current was being applied.

Turned off and back on TGHT power supply - this restarted things and now works again.

Have tapped back up to 35A, vacuum still good.

Restarting auto-ramp to 400A at 1.0A/min

 Monday, April 10, 2017, 13:13

Vacuum looks good.

IGP1 = 1.1e-7 Torr

TGHT = 127A, 1.30V

Increasing ramping rate to 2.0A/min

 Monday, April 10, 2017, 16:08

IGP1 = 1.5e-7 Torr

TGHT = 400A, 6.24V

OMEGA = 1510V

Increasing auto ramp setpoint to 450A at a rate of 0.2A/min

 Wednesday, April 12, 2017, 11:06

IGP1 = 2.96e-7 Torr

TGHT = 555A, 9.74V

OMEGA = 1935C

Has remained at max setpoints overnight.

Initiating auto-cool at 2.0A/min

 Thursday, April 13, 2017, 11:59

vented in air and opened up this morning.

container looks good.

see photo attached.

 Thursday, December 07, 2017, 09:57

Each endcap is wrapped in a separate piece of graphite foil and placed in a target boat.

There are also 4 coated springs, 2 on each side of the stack of endcaps.

The boat is wrapped with 3-layers of Ta heatshields.

Chamber pumped down overnight.

OMEGA slope = 0.98

HS water valves opened, no leaks detected.

IGP1 = 5.9e-7 Torr

IGP2 = 4.0e-7 Torr

Tapping up manually.

Final desired temperature = 1800C

Laura Lambert wrote:

Thursday, December 07, 2017, 09:57 Each endcap is wrapped in a separate piece of graphite foil and placed in a target boat. There are also 4 coated springs, 2 on each side of the stack of endcaps. The boat is wrapped with 3-layers of Ta heatshields. Chamber pumped down overnight. OMEGA slope = 0.98 HS water valves opened, no leaks detected. IGP1 = 5.9e-7 Torr IGP2 = 4.0e-7 Torr Tapping up manually. Final desired temperature = 1800C

 Thursday, December 07, 2017, 11:51

TGHT tripped off.

Turns out the vacuum limits have not been fully updated when they should have been and the old ones still apply.

IGP1 reached 8e-5 Torr which tripped off the system.

TGHT = 80A, 1.05V when the system tripped.

Laura Lambert wrote:

Laura Lambert wrote:  Thursday, December 07, 2017, 09:57 Each endcap is wrapped in a separate piece of graphite foil and placed in a target boat. There are also 4 coated springs, 2 on each side of the stack of endcaps. The boat is wrapped with 3-layers of Ta heatshields. Chamber pumped down overnight. OMEGA slope = 0.98 HS water valves opened, no leaks detected. IGP1 = 5.9e-7 Torr IGP2 = 4.0e-7 Torr Tapping up manually. Final desired temperature = 1800C    Thursday, December 07, 2017, 11:51 TGHT tripped off. Turns out the vacuum limits have not been fully updated when they should have been and the old ones still apply. IGP1 reached 8e-5 Torr which tripped off the system. TGHT = 80A, 1.05V when the system tripped.

 Friday, December 08, 2017, 15:29

Interlocks have been updated.

TGHT should now run up to 500mTorr before tripping off.

Laura Lambert wrote:

Laura Lambert wrote: Laura Lambert wrote:  Thursday, December 07, 2017, 09:57 Each endcap is wrapped in a separate piece of graphite foil and placed in a target boat. There are also 4 coated springs, 2 on each side of the stack of endcaps. The boat is wrapped with 3-layers of Ta heatshields. Chamber pumped down overnight. OMEGA slope = 0.98 HS water valves opened, no leaks detected. IGP1 = 5.9e-7 Torr IGP2 = 4.0e-7 Torr Tapping up manually. Final desired temperature = 1800C    Thursday, December 07, 2017, 11:51 TGHT tripped off. Turns out the vacuum limits have not been fully updated when they should have been and the old ones still apply. IGP1 reached 8e-5 Torr which tripped off the system. TGHT = 80A, 1.05V when the system tripped.    Friday, December 08, 2017, 15:29 Interlocks have been updated. TGHT should now run up to 500mTorr before tripping off.

Friday, December 08, 2017, 15:41

IGP1 = 2.8e-7 Torr

IGP2 = 1.9e-7 Torr

Tapped up manually to 50A

Initiated auto-ramp at a rate of 0.2A/min up to 300A.

Vacuum limit stop at 3.0e-5 Torr, backing off at 4.0e-5 Torr.

 Monday, December 11, 2017, 09:37

IGP1 = 2.4e-7

TGHT = 300A, 4.80V

OMEGA = 1175C

Tapping up manually...

 Monday, December 11, 2017, 14:19

Tapped up manually to 1800C

IGP1 = 2.1e-6 Torr

IGP2 = 2.1e-6 Torr

TGHT = 545A, 9.90V

OMEGA = 1810C

Will remain at max setpoints overnight and cool down in the a.m.

 Tuesday, December 12, 2017, 09:01

TGHT = 545A, 9.96V

OMEGA = 1833C

Remained at max setpoints for ~18hrs

IGP1 = 4.2e-7 Torr

IGP2 = 3.9e-7 Torr

Initiating auto-cool at 2.0A/min

 Wednesday, December 13, 2017, 11:05

Vented in air and removed from evap2 this morning.

Tuesday, June 04, 2019, 08:36

Each endcap is separated with a disc of graphite foil and rolled into packs of 5 within a foil envelope in a target boat.

There are also 4 coated springs, 2 on each side of the stack of endcaps.

The boat is wrapped with 3-layers of Ta heatshields.

Chamber pumped down overnight.

OMEGA slope = 0.99

IGP1 = 3.5e-7 Torr

Will Tap TGHT up manually to 40 A then autoramp to 400A at 1A/min.

Final desired temperature on OMEGA (tap)= 1800C

Tuesday, June 04, 2019, 11:54

IGP1= 6.1e-06 Torr

TGHT= 40 A

Begin autoramp to 400A at 1A/min

Out-gassing cycles observed.  Reduced autoramp to 0.5A/min

Currently TGHT=65A, 0.60 V

Wednesday, June 05, 2019, 08:27

TGHT = 321A, 4.9V @1149C

IGP1= 8.49 e-6 Torr

Set autoramp to 1A/min to530 A

Wednesday, June 05, 2019, 13:26

TGHT 530A, 9.2V

IGP1= 3.01e-05 Torr

OMEGA Temperature = 1689 Celsius

Set autoramp to 570A at 1A/min

 Wednesday, June 05, 2019, 15:51

Tapped manually to 1800 Celsius

TGHT 579A, 10.1V

IGP1= 2.06e-05 Torr

TGHT tapped down to 575A when OMEGA T ~1810 C

Thursday, June 06, 2019, 08:13

TGHT = 575A, 9.95V

OMEGA = 1809 C

IGP1 = 4.1e-7 Torr

Initiating auto-cool at -2.0A/min

Thursday, June 06, 2019, 16:00

After 1 hour  of TGHT at 0A and 0V, unloaded the Target boat.

Friday, October 04, 2019, 11:37

Each endcap is separated with a disc of graphite foil and rolled into packs of 5 within a foil envelope in a target boat.

There are also 3 coated springs, one in between endcaps and two on either end

The boat is wrapped with 2-layers of Ta heatshields.

Chamber pumping down

OMEGA slope = 0.99

Will Tap TGHT up manually to 40 A then autoramp to 400A at 1A/min.

Final desired temperature on OMEGA (tap)= 1800C

Monday, October 07, 2019, 09:08

Sunday night heating started at 1A/ min on TGHT to 54 A

heating paused for 1 hour to allow IGP1 to equillibrate.  Then restarted at 1A/min to 400A as planned. 

This morning IGP1 = 1.3e-06 Torr

TGHT = 401A, 4.2V

OMEGA = 1550 C

Monday, October 07, 2019, 09:36

manually tapping to 1800 C

Monday, October 07, 2019, 14:09

Temperature @ ~1800 for 3.5 hours

TGHT= 495.4, 9.2 V

IGP1= 1.1e-06 Torr Pressure Steady there begin cooling

Cooling @ -2A/min

Tuesday, May 07, 2024, 06:16

TP was swapped on previous day (May 6th)

protective screen installed.

Loaded 9 TaC coated end caps (groups of 4 and 5) and 2 TaC coated springs.

OMEGA Slope 0.99

Will heat to 1850-1900 C and hold for 4 hours

Good Vac = 5.0e-4 Torr

Bad Vac= 5.0 e-02 Torr

 Initial IGP1=6.7E-07 Torr

Friday, October 04, 2013, 15:37

A LP target container is coated with TaC.  The container is wrapped with 3 layers to heat shield.  

This container will be used for the graphite tube test.  

Chamber is being pumped down.

 The HS cooling water valves are open and no leaks are detected. 

TGHT will be ramped up to 580A at 0.2A/min

TBHT will be ramped up to 230A at 0.2A/min.

The temperature will be monitored and measured. 

 Sunday, October 06, 2013, 19:55

Tuesday, October 22, 2013, 16:49

The target was heated up to 580A and the temperature inside the tube was measured to be ~1800C and the outside surface was ~1400C.

The target was cooled down.  Then the graphite tube was inserted.

There are two thermcouples inserted inside the tube on both ends.

Chamber has been pumped down to 4.33 e-7 Torr.  No leaks were detected.

Target will be heated up again to TGHT @ 580A / TBHT @ 230A at 0.2A/min.

The temperatures will be monitored.

T1 = left (floating)

T2 = right (toughing C-grv tube)

(wtf ionizer pointing into the page).

 Thursday, October 24, 2013, 16:35

TGHT/TBHT reached to 580A/230A. 

T1 = 1642C

T2 = Error?? Reading goes on/off intermittently, showing 900 - 1900C

Thursday, October 24, 2013, 16:45 

Ramping up TGHT to 680A to see if T1 can reach 1700C.

IG1 currently at 5.2e-7 Torr.

 Friday, October 25, 2013, 12:30

TGHT was ramped up to 632A (stopped due to voltage limiting). 

T1 was measured at 1960C.  Vac went up as it was heated up.  (see attachment #2)

Target was cooled down at 5A/min, now at 0A.

The chamber will be vented and the target will be inspected.

This run is complete.

 Wednesday, February 28, 2018, 15:16

Container coated with TaC using 'flushing technique' and let dry.

Q-tip to plug ionizer became stuck in ionizer, removed manually with small drill bit.

Inspected ionizer with microscope, ionizer still good.

Cleaned ionizer tube with acetone.

Wrapped with 3 x Ta heat shields, incl center block

Currently pumping down in evap2

OMEGA slope = 0.98

Good vac at 3.0e-5, bad vac at 8.0e-5 Torr.

 Thursday, March 01, 2018, 10:06

HW water valves opened yesterday, no leaks detected.

IGP1 = 2.8e-7 Torr

Tapped up manually to 40A.

Waited ~3hrs

Vacuum stable.

IGP1 = 5.3e-7 Torr

IGP2 = 5.4e-7 Torr

Initiating auto ramp for TGHT @ 1.0A/min to a max setpoint of 350A

Initiating auto ramp for TBHT @ 0.5A/min to a max setpoint of 230A

Once max setpoints achieved, will tap up manually to final desired temperature of 1900C

 Thursday, March 01, 2018, 14:39

Vacuum started to climb very fast - auto-ramp was stopped.

Vacuum climbed up to IGP1 = 1.3e-4 Torr

Tapped TGHT back down to 80A from 90A, TBHT down to 50A from 60A.

Waited ~40min.

Vacuum stable, IGP1 = 2.6e-6 Torr

Restarting auto-ramp.

 Thursday, March 01, 2018, 14:54

IGP1 = 2.1e-5 Torr

Vacuum climbing quite rapidly again, stopped auto-ramp and vacuum started to drop right away.

TGHT = 100A

TBHT = 56A

Waited ~10min

IGP1 = 6.0e-6 Torr

IGP2 = 5.2e-6 Torr

Decreasing ramping rate to 0.5A/min and 0.2A/min for the TGHT and TBHT respectively, and re-initiating auto-ramp.

 Friday, March 02, 2018, 10:18

TGHT = 350A, 5.61V

TBHT = 230A, 4.04V

IGP1 = 4.3e-7 Torr

IGP2 = 3.8e-7 Torr

OMEGA = 1624C

Vacuum stable.

Increasing max setpoint of TGHT to 400A

Re-initiating auto-ramp of TGHT.

 Friday, March 02, 2018, 11:04

TGHT = 372A, 6.05V

IGP1 = 5.0e-7 Torr

Increasing ramping rate for TGHT to 1.0A/min

 Friday, March 02, 2018, 11:44

TGHT = 400A, 6.60V

IGP1 = 6.9e-7 Torr

OMEGA = 1780C

Vacuum stable.

Increasing max setpoint of TGHT to 430A

Re-initiating auto-ramp of TGHT.

 Friday, March 02, 2018, 12:17

TGHT = 430A, 7.22V

OMEGA = 1866C

IGP1 = 9.5e-7 Torr

Tapped up manually to OMEGA = 1910C

TGHT = 445A, 7.57V

TBHT = 230A, 4.07V

IGP1 = 1.1e-6 Torr

IGP2 = 9.9e-7 Torr

 Monday, March 05, 2018, 08:41

Remained at max setpoints over the weekend.

TGHT = 445A, 7.47V

TBHT = 230A, 4.06V

IGP1 = 1.87e-7 Torr

IGP2 = 1.47e-7 Torr

OMEGA = 1894C

Initiating auto-cool at 2.0A/min and 1.0A/min for the TGHT and TBHT respectively.

 Tuesday, March 20, 2018, 14:53

Vented in air.

Container was transferred to glove box for loading ~1 week ago

Container looks good.

 Monday, June 05, 2017, 15:20

Container coated with TaC using 'flushing technique' and let dry over weekend.

Cleaned ionizer tube with acetone, no coating inside ionizer tube.

Wrapped with 3 x Ta heat shields, incl center block

Currently pumping down in evap2

OMEGA slope = 0.98

Good vac at 3.0e-5, bad vac at 4.0e-5 Torr.

 Tuesday, June 06, 2017, 10:00

First time not turning water off and flushing lines after last use.

HS water valves have remained open since the last time evap2 was used [conditioning Ta#52]

No leak check done.

Tapped up manually to 35A.

Waited ~25min

Vacuum stable.

IGP1 = 2.9e-6 Torr

IGP2 = 4.8e-6 Torr

Initiating auto ramp for TGHT @ 0.2A/min to a max setpoint of 350A

Initiating auto ramp for TBHT @ 0.1A/min to a max setpoint of 230A

Once max setpoints achieved, will tap up manually to final desired temperature of 1900C

 Wednesday, June 07, 2017, 09:26

TGHT = 304A, 4.46V

TBHT = 169A, 2.769V

IGP1 = 6.1e-7 Torr

IGP2 = 7.3e-7 Torr

Vacuum stable.

Increasing ramping rate to 1.0A/min and 0.5A/min for the TGHT and TBHT respectively.

 Wednesday, June 07, 2017, 10:40

TGHT = 350A, 5.28V

TBHT = 203A, 3.39V

IGP1 = 1e-6 Torr

Increasing ramping rate for TBHT to 1.0A/min

Wednesday, June 07, 2017, 12:10 

TGHT = 350A, 5.26V

TBHT = 230A, 3.99V

IGP1 = 7.0e-7 Torr

IGP2 = 8.3e-7 Torr

OMEGA = 1600C

Vacuum stable.

Increasing max setpoint of TGHT to 400A

Re-initiating ramping rate of TGHT at 1.0A/min

 Wednesday, June 07, 2017, 15:42

Tapped up to reach final desired temperature.

TGHT = 450A, 7.28V

TBHT = 230A, 4.02V

IGP1 = 9.0e-7 Torr

IGP2 = 1.07e-6 Torr

OMEGA = 1910C

Will remain at max setpoints overnight.

 Thursday, June 08, 2017, 08:51

Remained at max setpoints for 17hrs.

TGHT = 450A, 7.28V

TBHT = 230A, 4.02V

IGP1 = 2.6e-7 Torr

IGP2 = 2.9e-7 Torr

OMEGA = 1899C

Initiating auto-cool at 2.0A/min and 1.0A/min for the TGHT and TBHT respectively.

 Thursday, June 08, 2017, 16:28

 Vented in air and taken out this afternoon.

Container looks good!

Transferred into glove box.

 Friday, May 22, 2015, 11:43

A target boat was sprayed with TaC coating and let dry yesterday.

The target boat is wrapped with 3-layers of Ta-heat shield.

The boat was installed in EVAP2, chamber is currently being pumped down.

 Friday, May 22, 2015, 14:22

HS water valves opened, no leaks detected.

IGP1 = 2.4e-6 Torr.

Tapping up manually...

 Friday, May 22, 2015, 14:33

Tapped up to 20A.

Vacuum jumped up to 7e-6 Torr.

Backed off to 5A before vacuum started to drop again.

IGP1 = 5e-6 Torr.

Tapping up manually again...just more slowly...

 Friday, May 22, 2015, 15:31

Tapped up to 12A, unable to tap up very fast due to volatile content in coating.

IGP1 = 3.6e-6 Torr.

Initiating auto-ramp at 0.1A/min with a max current of 580A.

 Monday, May 25, 2015, 09:03

IGP1 = 3e-7 Torr.

TGHT = 397.5A, 6.43V

Increasing ramping rate to 1.0A/min.

Laura Lambert wrote:

Friday, May 22, 2015, 11:43 A target boat was sprayed with TaC coating and let dry yesterday. The target boat is wrapped with 3-layers of Ta-heat shield. The boat was installed in EVAP2, chamber is currently being pumped down.  Friday, May 22, 2015, 14:22 HS water valves opened, no leaks detected. IGP1 = 2.4e-6 Torr. Tapping up manually...  Friday, May 22, 2015, 14:33 Tapped up to 20A. Vacuum jumped up to 7e-6 Torr. Backed off to 5A before vacuum started to drop again. IGP1 = 5e-6 Torr. Tapping up manually again...just more slowly...  Friday, May 22, 2015, 15:31 Tapped up to 12A, unable to tap up very fast due to volatile content in coating. IGP1 = 3.6e-6 Torr. Initiating auto-ramp at 0.1A/min with a max current of 580A.  Monday, May 25, 2015, 09:03 IGP1 = 3e-7 Torr. TGHT = 397.5A, 6.43V Increasing ramping rate to 1.0A/min.

 Monday, May 25, 2015, 17:06

TGHT at been at 580A for over 4 hours.  Cooling down in process at 1A/min. 

John Wong wrote:

Laura Lambert wrote:  Friday, May 22, 2015, 11:43 A target boat was sprayed with TaC coating and let dry yesterday. The target boat is wrapped with 3-layers of Ta-heat shield. The boat was installed in EVAP2, chamber is currently being pumped down.  Friday, May 22, 2015, 14:22 HS water valves opened, no leaks detected. IGP1 = 2.4e-6 Torr. Tapping up manually...  Friday, May 22, 2015, 14:33 Tapped up to 20A. Vacuum jumped up to 7e-6 Torr. Backed off to 5A before vacuum started to drop again. IGP1 = 5e-6 Torr. Tapping up manually again...just more slowly...  Friday, May 22, 2015, 15:31 Tapped up to 12A, unable to tap up very fast due to volatile content in coating. IGP1 = 3.6e-6 Torr. Initiating auto-ramp at 0.1A/min with a max current of 580A.  Monday, May 25, 2015, 09:03 IGP1 = 3e-7 Torr. TGHT = 397.5A, 6.43V Increasing ramping rate to 1.0A/min.    Monday, May 25, 2015, 17:06 TGHT at been at 580A for over 4 hours.  Cooling down in process at 1A/min.

 Vented in air and opened up this morning.

Target boat looks good! fully sintered! 

 Friday, February 03, 2017, 14:17

The endcaps are stacked together with a punched out disc of graphite foil placed in between each endcap for separation so endcaps won't fuse together.

The end caps are further wrapped in a larger piece of graphite foil to hold together as a tube [same method used in elogID # 158 and 235]

There are also 4 coated springs, 2 on each side of the endcaps tube, with the endcaps tube residing in the middle of the boat.

The boat is wrapped with 3-layers of Ta heatshields.

Chamber is currently being pumped down.

Good vac at 3.0e-5, bad vac at 4.0e-5 Torr.

OMEGA slope = 0.98

 Monday, February 06, 2017, 09:29

Power outage this weekend and evap2 tripped off.

Re-pumping down now...

 Tuesday, February 07, 2017, 08:54

HS water valves opened, no leaks detected.

IGP1 = 1.9e-7 Torr

Tapped up manually to 35A

Vacuum stable.

IGP1 = 2.0e-7 Torr

Initiating auto-ramp at 0.2A/min with a final setpoint of 450A.

Final desired temperature = 1800C

 Wednesday, February 08, 2017, 09:52

IGP1 = 2.98e-7 Torr

TGHT = 325A, 3.5V

Vacuum stable.

Increasing ramping rate to 1.0A/min

 Wednesday, February 08, 2017, 11:46

IGP1 = 6.3e-7 Torr

TGHT = 433A, 4.89V

Increasing max setpoint to TGHT = 500A

OMEGA has still yet to show a temperature...should be reading points at this high in current

Will go down to the lab and follow up on OMEGA settings to confirm everything is set up ok before proceeding to a higher current...

 Wednesday, February 08, 2017, 16:03

IGP1 = 4e-7 Torr

TGHT = 500A, 5.75V

OMEGA still not reading

Initiating auto-cool at -2A/min

Will update elog with more details tomorrow

 Thursday, February 09, 2017, 10:52

Evap2 was cooled down and opened up this morning.

Turns out both legs on the target boat were touching the new heatshield and therefore had been loosing power.

Normally a boat at 500A would read ~1800C, in this scenario at 500A the boat read ~1000C.

A lot of power was being lost into the heatshield.

See photos attached of target boat sitting at 500A.

The heatshield is currently being ground down in those two spots to accommodate the target boat.

Laura Lambert wrote:

Friday, February 03, 2017, 14:17 The endcaps are stacked together with a punched out disc of graphite foil placed in between each endcap for separation so endcaps won't fuse together. The end caps are further wrapped in a larger piece of graphite foil to hold together as a tube [same method used in elogID # 158 and 235] There are also 4 coated springs, 2 on each side of the endcaps tube, with the endcaps tube residing in the middle of the boat. The boat is wrapped with 3-layers of Ta heatshields. Chamber is currently being pumped down. Good vac at 3.0e-5, bad vac at 4.0e-5 Torr. OMEGA slope = 0.98  Monday, February 06, 2017, 09:29 Power outage this weekend and evap2 tripped off. Re-pumping down now...  Tuesday, February 07, 2017, 08:54 HS water valves opened, no leaks detected. IGP1 = 1.9e-7 Torr Tapped up manually to 35A Vacuum stable. IGP1 = 2.0e-7 Torr Initiating auto-ramp at 0.2A/min with a final setpoint of 450A. Final desired temperature = 1800C  Wednesday, February 08, 2017, 09:52 IGP1 = 2.98e-7 Torr TGHT = 325A, 3.5V Vacuum stable. Increasing ramping rate to 1.0A/min  Wednesday, February 08, 2017, 11:46 IGP1 = 6.3e-7 Torr TGHT = 433A, 4.89V Increasing max setpoint to TGHT = 500A OMEGA has still yet to show a temperature...should be reading points at this high in current Will go down to the lab and follow up on OMEGA settings to confirm everything is set up ok before proceeding to a higher current...  Wednesday, February 08, 2017, 16:03 IGP1 = 4e-7 Torr TGHT = 500A, 5.75V OMEGA still not reading Initiating auto-cool at -2A/min Will update elog with more details tomorrow  Thursday, February 09, 2017, 10:52 Evap2 was cooled down and opened up this morning. Turns out both legs on the target boat were touching the new heatshield and therefore had been loosing power. Normally a boat at 500A would read ~1800C, in this scenario at 500A the boat read ~1000C. A lot of power was being lost into the heatshield. See photos attached of target boat sitting at 500A. The heatshield is currently being ground down in those two spots to accommodate the target boat.

 Tuesday, February 14, 2017, 15:43

Heatshield was ground back and target boat now fits nicely into heatshield without contact.

Laura Lambert wrote:

Laura Lambert wrote:  Friday, February 03, 2017, 14:17 The endcaps are stacked together with a punched out disc of graphite foil placed in between each endcap for separation so endcaps won't fuse together. The end caps are further wrapped in a larger piece of graphite foil to hold together as a tube [same method used in elogID # 158 and 235] There are also 4 coated springs, 2 on each side of the endcaps tube, with the endcaps tube residing in the middle of the boat. The boat is wrapped with 3-layers of Ta heatshields. Chamber is currently being pumped down. Good vac at 3.0e-5, bad vac at 4.0e-5 Torr. OMEGA slope = 0.98  Monday, February 06, 2017, 09:29 Power outage this weekend and evap2 tripped off. Re-pumping down now...  Tuesday, February 07, 2017, 08:54 HS water valves opened, no leaks detected. IGP1 = 1.9e-7 Torr Tapped up manually to 35A Vacuum stable. IGP1 = 2.0e-7 Torr Initiating auto-ramp at 0.2A/min with a final setpoint of 450A. Final desired temperature = 1800C  Wednesday, February 08, 2017, 09:52 IGP1 = 2.98e-7 Torr TGHT = 325A, 3.5V Vacuum stable. Increasing ramping rate to 1.0A/min  Wednesday, February 08, 2017, 11:46 IGP1 = 6.3e-7 Torr TGHT = 433A, 4.89V Increasing max setpoint to TGHT = 500A OMEGA has still yet to show a temperature...should be reading points at this high in current Will go down to the lab and follow up on OMEGA settings to confirm everything is set up ok before proceeding to a higher current...  Wednesday, February 08, 2017, 16:03 IGP1 = 4e-7 Torr TGHT = 500A, 5.75V OMEGA still not reading Initiating auto-cool at -2A/min Will update elog with more details tomorrow  Thursday, February 09, 2017, 10:52 Evap2 was cooled down and opened up this morning. Turns out both legs on the target boat were touching the new heatshield and therefore had been loosing power. Normally a boat at 500A would read ~1800C, in this scenario at 500A the boat read ~1000C. A lot of power was being lost into the heatshield. See photos attached of target boat sitting at 500A. The heatshield is currently being ground down in those two spots to accommodate the target boat.    Tuesday, February 14, 2017, 15:43 Heatshield was ground back and target boat now fits nicely into heatshield without contact.

 Tuesday, February 14, 2017, 15:44

Boat with endcaps and springs reloaded today and pumped back down this afternoon.

HS water valves opened, no leaks detected.

Tapped up manually to 35A

Vacuum stable.

IGP1 = 3.5e-6 Torr

Initiating auto-ramp at 0.2A/min with a final setpoint of 400A.

Final desired temperature = 1800C

 Wednesday, February 15, 2017, 10:24

IGP1 = 7.2e-7 Torr

TGHT = 260A, 3.95V

OMEGA = 1158C

Vacuum stable.

Increasing ramping rate to 1.0A/min.

 Wednesday, February 15, 2017, 13:02

IGP1 = 2.0e-6 Torr

TGHT = 400A, 6.67V

OMEGA = 1530C

Increasing final setpoint to 450A

 Wednesday, February 15, 2017, 13:55

IGP1 = 2.5e-6 Torr

TGHT =450A, 7.7V

OMEGA = 1640C

Increasing final setpoint to 500A

 Wednesday, February 15, 2017, 15:13

IGP1 = 1.8e-6 Torr

TGHT = 500A, 8.59V

OMEGA = 1770C

MIKRON = 1740C

Tapping up manually to ~1800C...

 Thursday, February 16, 2017, 09:09

IGP1 = 5.28e-7 Torr

TGHT = 520A, 9.1V

OMEGA = 1821C

Target boat has remained at max setpoints for 17.5hrs.

Initiating auto-cool at 1A/min

 Thursday, February 16, 2017, 13:49

Increasing auto-cool to 2.0A/min

 Friday, February 17, 2017, 16:00

Vented in air and opened up today.

Endcaps looks good  see photos attached

 Thursday, May 28, 2015, 11:34

Endcaps were sintered [see elog#199]

A Ta foil is placed in the target boat with separate slots for each endcap [see image]

The target boat is wrapped with 3-layers of Ta-heat shield.

The boat is installed in EVAP2, chamber is currently being pumped down.

 Thursday, May 28, 2015, 14:01

HS water valves opened, no leaks detected.

IGP1 = 1.4e-6 Torr.

Initiating manual tap up.

 Thursday, May 28, 2015, 15:10

Manually tapped up TGHT  to 108A, 1.1V

Initiating auto-ramp at 2.0A/min with a max setpoint of 300A

 Thursday, May 28, 2015, 15:22

Hoping to speed up the process...

IGP1 = 1.0e-6 Torr.

Increasing ramping rate to 4.0A/min with a max setpoint of 500A

Final desired temperature = 1800C