Marla Cervantes wrote:

Thursday, February 08, 2018, 14:50 35 circles from cast#2 of 14 mm diameter were packed into a graphite sample container. 35 x UO2/C circles = 4.76 g Graphite container = 5.3 g Graphite tube is placed inside a target boat. Boat previously coated with TaC and sintered. Ta-target boat is wrapped with 3 new Ta foils for heat shielding and the boat was installed in Evap1. Chamber currently pumping down.  Friday, February 09, 2018, 10:40 Initial IGP1 = 4.54e-7 Torr Tapped up entire process manually to 520A in 25 min TGHT = 520 A, 5.49 V Vacuum coming down indicating carbonization process complete.   Current suddenly tripped off from 520 A to 0 A. There was not a power outage. There was good vacuum. Water cooling did not trip off

 Friday, February 09, 2018, 16:49

The power supply was tested and its working normally.

Apparently a glitch on EPICS caused the tripped off.

Marla Cervantes wrote:

Marla Cervantes wrote:  Thursday, February 08, 2018, 14:50 35 circles from cast#2 of 14 mm diameter were packed into a graphite sample container. 35 x UO2/C circles = 4.76 g Graphite container = 5.3 g Graphite tube is placed inside a target boat. Boat previously coated with TaC and sintered. Ta-target boat is wrapped with 3 new Ta foils for heat shielding and the boat was installed in Evap1. Chamber currently pumping down.  Friday, February 09, 2018, 10:40 Initial IGP1 = 4.54e-7 Torr Tapped up entire process manually to 520A in 25 min TGHT = 520 A, 5.49 V Vacuum coming down indicating carbonization process complete.   Current suddenly tripped off from 520 A to 0 A. There was not a power outage. There was good vacuum. Water cooling did not trip off     Friday, February 09, 2018, 16:49 The power supply was tested and its working normally. Apparently a glitch on EPICS caused the tripped off.

 Friday, February 09, 2018, 17:00

Target remained in EVAP1 for 2 hours at 0 A to ensure cooling.

EVAP1 was vented with Ar and the target was removed from EVAP1.

Graphite container seems unbroken.

Ta boat looks unbroken.

 Tuesday, February 13, 2018, 11:39

35 circles of 14 mm diameter were packed into a graphite sample container.

35 x UO2/C circles = 5.74 g

Graphite container = 5.20 g

Graphite tube is placed inside a target boat.

Boat previously coated with TaC and sintered.

Ta-target boat is wrapped with 3 used Ta foils for heat shielding and the boat was installed in Evap1.

Chamber currently pumping down.

 Tuesday, February 13, 2018, 15:30

Initial IGP1 = 2.73x10e-6 Torr

Tapped up entire process manually to 520 A in 30 min

TGHT = 520 A, 5.41 V

Vacuum coming down nicely indicating carbonization process complete.

Current trip off after 5 min of being at 520 A.

 Wednesday, February 14, 2018, 15:32

EVAP1 vented with Argon and the target was removed.

Target was transferred to glove box.

Ta boat and graphite container look unbroken.

 Wednesday, February 28, 2018, 15:19

Last two rounds of materials in evap1 have tripped off the TGHT in epics within minutes of the target reaching 520A.

Loaded an empty target boat, no heat shields.

Will ramp up with same speed as last two samples to see how TGHT reacts and whether a trip is induced or not.

Currently pumping down now.

 Thursday, March 01, 2018, 13:53

IGP1 = 9.6e-7 Torr

Tapped up to 100A @ 1.0A/s, waited ~6min

IGP1 = 1.77e-6 Torr

Tapped up 40A/min to 140A, waited ~2min

Tapped up 40A/min to 180A, waited ~2min

Tapped up @ a rate of 1.0A/s for 40sec, then wait 20sec. Used this rate consistently up to 520A.

TGHT = 520A, 5.75V

Friday, March 02, 2018, 10:09 

TGHT = 520A, 5.81V this morning.

TGHT still on! 

No trip induced.

IGP1 = 1.7e-6 Torr.

Initiating auto-cool at 2.0A/min

 Thursday, March 05, 2018, 14:07

Container removed, test complete.

Marla Cervantes wrote:

Tuesday, February 13, 2018, 11:39 35 circles of 14 mm diameter were packed into a graphite sample container. 35 x UO2/C circles = 5.74 g Graphite container = 5.20 g Graphite tube is placed inside a target boat. Boat previously coated with TaC and sintered. Ta-target boat is wrapped with 3 used Ta foils for heat shielding and the boat was installed in Evap1. Chamber currently pumping down.  Tuesday, February 13, 2018, 15:30 Initial IGP1 = 2.73x10e-6 Torr Tapped up entire process manually to 520 A in 30 min TGHT = 520 A, 5.41 V Vacuum coming down nicely indicating carbonization process complete. Current trip off after 5 min of being at 520 A.  Wednesday, February 14, 2018, 15:32 EVAP1 vented with Argon and the target was removed. Target was transferred to glove box. Ta boat and graphite container look unbroken.

 Friday, March 02, 2018, 16:31

A test was performed in EVAP1 (see log ID 194):

- A Ta boat without Ta shielding was submitted to 520 A and it remained at that current point overnight.

-No trip off

Marla Cervantes wrote:

Marla Cervantes wrote:  Tuesday, February 13, 2018, 11:39 35 circles of 14 mm diameter were packed into a graphite sample container. 35 x UO2/C circles = 5.74 g Graphite container = 5.20 g Graphite tube is placed inside a target boat. Boat previously coated with TaC and sintered. Ta-target boat is wrapped with 3 used Ta foils for heat shielding and the boat was installed in Evap1. Chamber currently pumping down.  Tuesday, February 13, 2018, 15:30 Initial IGP1 = 2.73x10e-6 Torr Tapped up entire process manually to 520 A in 30 min TGHT = 520 A, 5.41 V Vacuum coming down nicely indicating carbonization process complete. Current trip off after 5 min of being at 520 A.  Wednesday, February 14, 2018, 15:32 EVAP1 vented with Argon and the target was removed. Target was transferred to glove box. Ta boat and graphite container look unbroken.  Friday, March 02, 2018, 16:31 A test was performed in EVAP1 (see log ID 194): - A Ta boat without Ta shielding was submitted to 520 A and it remained at that current point overnight. -No trip off

 Monday, March 12, 2018, 9:13

35 circles from cast#2 of 14 mm diameter were packed into a graphite sample container.

35 x UO2/C circles = 5.21 g

Graphite container = 6.85 g

Graphite tube is placed inside a target boat.

Boat previously coated with TaC and sintered.

Ta-target boat is wrapped with 3 Ta foils for heat shielding and the boat was installed in Evap1.

Chamber currently pumping down.

 Monday, March 12, 2018, 13:57

Initial IGP1 = 4.79e-7 Torr

Tapped up entire process manually to 520A in 30 min

TGHT = 520 A, 5.32 V

Vacuum coming down indicating carbonization process complete.  

Will remain at max setpoint for 1 hrs to ensure full carbonization before cooling down.

 Monday, March 12, 2018, 14:57 

Cooling down rate used 3 A/10s.

 Tuesday, March 13, 2018, 18:22

Vented with Ar and removed from EVAP1

 Wednesday, March 28, 2018, 11:35

D-shaped discs were cut from cast 2, the same as the last sample of 1stepUCx [see elog i.d. 197]

A 13mm punch was used to punch out discs from pre-cut strips using the old method.

The target consists of 195 discs with 8.1cm in length - all single discs, no packs.

195 x UO2/C discs = 19.79g

Graphite insert is placed inside a target boat with both endcaps on.

Boat previously coated with TaC and sintered.

Ta-target boat is wrapped with 3-layers of heat shield and installed in evap1 yesterday afternoon.

Chamber pumped down overnight.

 Wednesday, March 28, 2018, 13:33

IGP1 = 4.03e-7 Torr

Tapped up TGHT manually to 80A, 0.83V - waited 50min, vacuum started to drop/stabilize.

Continued to tap up manually to 430A, 4.22V

Started out slow with a rate of ~10A/5min, and slowly increased to a rate of ~10A/min as vacuum stabilized, slowing down again when reaching carbonization outgassing.

Auto ramp at 0.2A/min from 430A-520A.

Thursday, March 29, 2018, 10:04

Reached 520A around 2am.

TGHT = 520A, 5.13V

IGP1 = 1.74e-6 Torr

Initiated auto-cool this morning at a rate of 1.0A/min.

Laura Lambert wrote:

Wednesday, March 28, 2018, 11:35 D-shaped discs were cut from cast 2, the same as the last sample of 1stepUCx [see elog i.d. 197] A 13mm punch was used to punch out discs from pre-cut strips using the old method. The target consists of 195 discs with 8.1cm in length - all single discs, no packs. 195 x UO2/C discs = 19.79g Graphite insert is placed inside a target boat with both endcaps on. Boat previously coated with TaC and sintered. Ta-target boat is wrapped with 3-layers of heat shield and installed in evap1 yesterday afternoon. Chamber pumped down overnight.  Wednesday, March 28, 2018, 13:33 IGP1 = 4.03e-7 Torr Tapped up TGHT manually to 80A, 0.83V - waited 50min, vacuum started to drop/stabilize. Continued to tap up manually to 430A, 4.22V Started out slow with a rate of ~10A/5min, and slowly increased to a rate of ~10A/min as vacuum stabilized, slowing down again when reaching carbonization outgassing. Auto ramp at 0.2A/min from 430A-520A. Thursday, March 29, 2018, 10:04 Reached 520A around 2am. TGHT = 520A, 5.13V IGP1 = 1.74e-6 Torr Initiated auto-cool this morning at a rate of 1.0A/min.

 Monday, April 09, 2018, 16:00

ISAC controls performed a PLC switch over compromising the nuclear ventilation controls WITHOUT NOTIFYING ME  

This is the 2nd time in a month this has happened without being notified.

Evap1 has therefore tripped.

During this switch there was a problem which caused the turn over to take even longer.

Sat here tapping reset until nuclear ventilation was 'back on'.

Vacuum proceeded to drop once the tests were complete, then started to spike again, nuc vent remained not ok after tests were done nuc vent ok.

Laura Lambert wrote:

Laura Lambert wrote:  Wednesday, March 28, 2018, 11:35 D-shaped discs were cut from cast 2, the same as the last sample of 1stepUCx [see elog i.d. 197] A 13mm punch was used to punch out discs from pre-cut strips using the old method. The target consists of 195 discs with 8.1cm in length - all single discs, no packs. 195 x UO2/C discs = 19.79g Graphite insert is placed inside a target boat with both endcaps on. Boat previously coated with TaC and sintered. Ta-target boat is wrapped with 3-layers of heat shield and installed in evap1 yesterday afternoon. Chamber pumped down overnight.  Wednesday, March 28, 2018, 13:33 IGP1 = 4.03e-7 Torr Tapped up TGHT manually to 80A, 0.83V - waited 50min, vacuum started to drop/stabilize. Continued to tap up manually to 430A, 4.22V Started out slow with a rate of ~10A/5min, and slowly increased to a rate of ~10A/min as vacuum stabilized, slowing down again when reaching carbonization outgassing. Auto ramp at 0.2A/min from 430A-520A. Thursday, March 29, 2018, 10:04 Reached 520A around 2am. TGHT = 520A, 5.13V IGP1 = 1.74e-6 Torr Initiated auto-cool this morning at a rate of 1.0A/min.    Monday, April 09, 2018, 16:00 ISAC controls performed a PLC switch over compromising the nuclear ventilation controls WITHOUT NOTIFYING ME   This is the 2nd time in a month this has happened without being notified. Evap1 has therefore tripped. During this switch there was a problem which caused the turn over to take even longer. Sat here tapping reset until nuclear ventilation was 'back on'. Vacuum proceeded to drop once the tests were complete, then started to spike again, nuc vent remained not ok after tests were done nuc vent ok.

 Monday, April 09, 2018, 16:52

Turns out I wasn't on a list of ppl who need to know about this test when I should be

They also didn't reset the alarms locally outside the hot lab so nuc vent remained not ok until this was reset.

IGP1 reached 0.027 Torr before nuc vent was ok and pumps were able to be turned back on 

Pumps back on IGP1 = 1.86e-5 Torr and still pumping down

Laura Lambert wrote:

Laura Lambert wrote: Laura Lambert wrote:  Wednesday, March 28, 2018, 11:35 D-shaped discs were cut from cast 2, the same as the last sample of 1stepUCx [see elog i.d. 197] A 13mm punch was used to punch out discs from pre-cut strips using the old method. The target consists of 195 discs with 8.1cm in length - all single discs, no packs. 195 x UO2/C discs = 19.79g Graphite insert is placed inside a target boat with both endcaps on. Boat previously coated with TaC and sintered. Ta-target boat is wrapped with 3-layers of heat shield and installed in evap1 yesterday afternoon. Chamber pumped down overnight.  Wednesday, March 28, 2018, 13:33 IGP1 = 4.03e-7 Torr Tapped up TGHT manually to 80A, 0.83V - waited 50min, vacuum started to drop/stabilize. Continued to tap up manually to 430A, 4.22V Started out slow with a rate of ~10A/5min, and slowly increased to a rate of ~10A/min as vacuum stabilized, slowing down again when reaching carbonization outgassing. Auto ramp at 0.2A/min from 430A-520A. Thursday, March 29, 2018, 10:04 Reached 520A around 2am. TGHT = 520A, 5.13V IGP1 = 1.74e-6 Torr Initiated auto-cool this morning at a rate of 1.0A/min.    Monday, April 09, 2018, 16:00 ISAC controls performed a PLC switch over compromising the nuclear ventilation controls WITHOUT NOTIFYING ME   This is the 2nd time in a month this has happened without being notified. Evap1 has therefore tripped. During this switch there was a problem which caused the turn over to take even longer. Sat here tapping reset until nuclear ventilation was 'back on'. Vacuum proceeded to drop once the tests were complete, then started to spike again, nuc vent remained not ok after tests were done nuc vent ok.    Monday, April 09, 2018, 16:52 Turns out I wasn't on a list of ppl who need to know about this test when I should be They also didn't reset the alarms locally outside the hot lab so nuc vent remained not ok until this was reset. IGP1 reached 0.027 Torr before nuc vent was ok and pumps were able to be turned back on  Pumps back on IGP1 = 1.86e-5 Torr and still pumping down

 Tuesday, April 10, 2018, 14:46

Glove box fixed!

Vented in Argon and transferred to glove box.

Graphite insert has moved to within 1mm of the end of the left side of the boat.

This could have happened during removal from evap1, hard to tell.

Either way, clearly a looser fit of the graphite insert in the boat indicating possible shrinkage of graphite insert.

 Tuesday, April 17, 2018, 10:30

UO2/C green was prepared April 12th, 2018

The cast peeled off the glass nicely April 13th, 2018

Initial UO2 powder used = 50.56g (Inventory R-01032A, UO2 + bottle = 626.28g before use)

Graphite powder used = 10.38g

Green cast dried UO2/C + organic mass = 61.40g 

The green was rolled up and wrapped in a piece of graphite sheet.

The Ta-target boat was wrapped with 3-layers of heat shield [1 reused, 2 new] and installed in evap1 yesterday.

Chamber pumped down overnight.

IGP1 = 8.4e-7 Torr

Tapped up to 35A, 0.46V

Waited ~135min, vacuum stable.

IGP1 = 1.6e-5 Torr

Initiating auto-ramp at 0.2A/min

Target boat will be ramped up to 520A.

Vacuum limit stop at 3.0e-4 Torr, backing off at 6.0e-4 Torr.

 Wednesday, April 18, 2018, 09:21

IGP1 = 9.6e-6 Torr

TGHT = 245A, 2.10V

Vacuum stable, increasing ramping rate to 0.5A/min.

 Thursday, April 19, 2018, 08:35

IGP1 = 3.21e-6 Torr

Materials have finished carbonizing.

TGHT = 520A, 4.97V

Evap1 has remained at max setpoints for ~6.5hrs

Initiating auto-cool at 1.0A/min

 Thursday, May 10, 2018, 10:33

Materials were vented in Ar and transferred to glove box on April 20th

 Friday, May 18, 2018, 18:32

35 circles of 14 mm diameter of cast #3 were packed into a graphite sample container.

40 x UO2/C circles = 4.58 g

Graphite container mass = 6.95 g

Graphite tube is placed inside a target boat.

Boat previously coated with TaC and sintered.

Ta-target boat is wrapped with 3 used Ta foils for heat shielding and the boat was installed in Evap1.

Chamber currently pumping down.

Saturday, May 19, 2018, 07:30 

Initial IGP1 = 6.27e-7 Torr

 Tapped to 80A at 10A/10s with 20 s waiting period each 10 A

 Waited 4 min for vacuum to stabilize.

 Tapped to 100 A at 10A/10s with 20 s waiting period each 10 A

 Waited 12 min for vacuum

Tapped to 400 A at 25A/30s with 30 s waiting period each 25 A

Tapped to 520 A at 20A/30s with 30 s waiting period each 20 A

Pressure dropping indicates carbonization complete.

Current tripped off, vacuum was ok, water cooling was ok.

Saturday, May 19, 2018, 10:00 

Current was returned to 520 A manually

Tapped to 100 A at 10A/10s with 20 s waiting period each 10 A 

Tapped to 400 A at 25A/30s with 30 s waiting period each 25 A

Tapped to 520 A at 20A/30s with 30 s waiting period each 20 A

The discs will stay at max current for 4 hrs

 Saturday, May 19, 2018, 18:31

Vented with Argon and removed form evaporator 1

Friday, May 25, 2018, 15:34 

D-shaped discs were cut from cast 3

A 13mm punch was used to punch out discs from pre-cut strips using the old method.

The target consists of 205 discs with 10 cm in length - all single discs, no packs.

205 x UO₂/C discs = 22.04 g

Graphite insert with caps is placed inside a target boat.

Boat previously coated with TaC and sintered.

Ta-target boat is wrapped with 3-layers of heat shield and installed in evap1.

Chamber is pumping down.

 Saturday, May 26, 2018, 10:39

Current tapped manually to 80 A at 1A/s in 10 A blocks with a waiting period of 20 s between each increment

18 min waiting for pressure stabilization

Current tapped to 100 A in same rate

Saturday, May 26, 2018, 10:51 

After 9 min current was reduced to 60 A to reduce pressure.

Cuerrent was tapped to 100 A

After 10 min the rate was increased to 25 A each 20 s until 450 A

The rate was changed to 10 A each 2 min until 500 A

Last 20 A were tapped after 1 min 

Saturday, May 26, 2018, 15:41 

After 4hrs the current was reduced in a rate of 10 A /min

Monday, May 28, 2018, 12:45 

EVAPI was vented with Ar and UCx was transferred to glove box.

 Friday, June 01, 2018, 11:20

Target boat was previously coated with TaC and sintered.

Two small C-inserts of ~2cm length were placed on Ta boat

Sample 1-sc: 15 discs of cast 3 made with 1-step cast method (UCx+foil 1.437 g)

Sample 2-sc: 24 discs from rejected discs of 2-step casting (UCx+foil 1.585 g)

Ta boat was wrapped with 3 layers of Ta-heat shield

The chamber is currently pumping down.

TGHT will be ramped up to 495A [same parameters used to reach 1910C in evap2 when sintering TaC coating - elog410 evap2]

Monday, June 04, 2018, 11:27 

IG1 = 4e-7 Torr

Tapped up manually to 35A

Waited 1hr

Vacuum stable.

IG1 = 8.02e-7 Torr.

Initiating auto-ramp (0.1 A/min) up to 80 A

 Tuesday, June 07, 2018, 15:47

Vacuum stable

IG1 = 7.02e-7 Torr.

Changing auto-ramp to 0.02 A/min up to 140 A

Thursday, June 07, 2018, 15:49 

Vacuum stable 5.5e-7 Torr

Current 139 A, voltage 1.25 V

Changing auto-ramp to 0.1 A/min up to 495 

Saturday, June 9, 2018, 10:41 

The material stayed 4 hours at 495 A

Auto-ramp set to -1 A/min down to 0 A 

Monday, June 11, 2018, 17:43 

EVAPI was vented with Ar and UCx was transferred to glove box

 Tuesday, June 12, 2018, 18:20

35 circles of 14 mm diameter of cast #4 were packed into a graphite sample container.

30 x UO₂/C circles = 4.07 g

Graphite container mass = 5.3 g

Graphite tube is placed inside a target boat.

Boat previously coated with TaC and sintered.

Ta-target boat is wrapped with 3 used Ta foils for heat shielding and the boat was installed in Evap1.

Chamber currently pumping down.

Wednesday, June 13, 2018, 10:29 

Initial IGP1 = 6.43e-7 Torr

Tapped to 80A at 10A/10s with 20 s waiting period each 10 A

Waited 5 min for vacuum to stabilize.

Tapped to 90 A at 10A/10s with 20 s waiting period each 10 A

Waited 5 min to tap to 100 A 

Waited 14 min for vacuum to stabilize

Tapped to 400 A at 25A/30s with 30 s waiting period each 25 A

Tapped to 520 A at 20A/30s with 30 s waiting period each 20 A

Max pressure ~0.06 Torr 

Marla Cervantes wrote:

Tuesday, June 12, 2018, 18:20 35 circles of 14 mm diameter of cast #4 were packed into a graphite sample container. 30 x UO2/C circles = 4.07 g Graphite container mass = 5.3 g Graphite tube is placed inside a target boat. Boat previously coated with TaC and sintered. Ta-target boat is wrapped with 3 used Ta foils for heat shielding and the boat was installed in Evap1. Chamber currently pumping down. Wednesday, June 13, 2018, 10:29  Initial IGP1 = 6.43e-7 Torr Tapped to 80A at 10A/10s with 20 s waiting period each 10 A Waited 5 min for vacuum to stabilize. Tapped to 90 A at 10A/10s with 20 s waiting period each 10 A Waited 5 min to tap to 100 A  Waited 14 min for vacuum to stabilize Tapped to 400 A at 25A/30s with 30 s waiting period each 25 A Tapped to 520 A at 20A/30s with 30 s waiting period each 20 A Max pressure ~0.06 Torr

 Wednesday, June 13, 2018, 11:08

Pressure was dropping indicating full carbothermal reduction but the current tripped off to 0 A.

Marla Cervantes wrote:

Marla Cervantes wrote:  Tuesday, June 12, 2018, 18:20 35 circles of 14 mm diameter of cast #4 were packed into a graphite sample container. 30 x UO2/C circles = 4.07 g Graphite container mass = 5.3 g Graphite tube is placed inside a target boat. Boat previously coated with TaC and sintered. Ta-target boat is wrapped with 3 used Ta foils for heat shielding and the boat was installed in Evap1. Chamber currently pumping down. Wednesday, June 13, 2018, 10:29  Initial IGP1 = 6.43e-7 Torr Tapped to 80A at 10A/10s with 20 s waiting period each 10 A Waited 5 min for vacuum to stabilize. Tapped to 90 A at 10A/10s with 20 s waiting period each 10 A Waited 5 min to tap to 100 A  Waited 14 min for vacuum to stabilize Tapped to 400 A at 25A/30s with 30 s waiting period each 25 A Tapped to 520 A at 20A/30s with 30 s waiting period each 20 A Max pressure ~0.06 Torr   Wednesday, June 13, 2018, 11:08 Pressure was dropping indicating full carbothermal reduction but the current tripped off to 0 A.

 Wednesday, June 13, 2018, 12:23

The problem was reported to controls group

After 1 hour at 0 A, the autoramp was set to 4 A/min up to 520 A

The current and voltage are increasing accordingly.

The material will stay 4 hours at max point.

Thursday, June 14, 2018, 09:14 

After 4 hours the auto ramp was set to -1A/min to 0 A

Thursday, June 14, 2018, 14:47 

The IEVAP  was vented with Ar and the UCx was trasnferred to the glove box.

 Friday, June 15, 2018, 16:39

35 circles of 14 mm diameter of cast #3 were packed into a graphite sample container.

35 x UO₂/C circles = 4.07 g

Graphite container mass = 5.3 g

Graphite tube is placed inside a target boat.

Boat previously coated with TaC and sintered.

Ta-target boat is wrapped with 3 used Ta foils for heat shielding and the boat was installed in Evap1.

Chamber currently pumping down.

 Saturday, June 16, 2018, 15:00

Tapped to 80A at 10A/10s with 20 s waiting period each 10 A

Waited 5 min for vacuum to stabilize.

Tapped to 90 A at 10A/10s with 20 s waiting period each 10 A

Waited 14 min for vacuum to stabilize

Tapped to 100 A at 10A/10s with 20 s waiting period each 10 A

Tapped to 520 A at 20A/20s with 20 s waiting period each 20 A

 Tuesday, June 19, 2018, 15:51 

 The material will be in the evap for a week

Wednesday, June 27, 2018, 09:53 

 The IEVAP  was vented with Ar and the UCx was trasnferred to the glove box.

Wednesday, July 11, 2018, 17:41

Cast prepared by Marla (see note in Hotlab)

Target boat contained about 50g UO2 powder. 

TGHT will be ramped up to 520A.

Vacuum limit stop at 3.0 e-4 Torr, backing off at 6.0e-4 Torr. 

Chamber is currently being pumped down

 Thursday, July 12, 2018, 10:45

Pressure at 8.9e-7 Torr. 

Initiate auto ramping TGHT at 0.1A/min to reach 580A (will monitor vacuum to ensure complete carbonization)

 Wednesday, July 18, 2018, 10:23

TGTH at 369A/3.7V, carbonization in progress. 

Pressure limited was set to 5.0e-5 Torr; change limit to 6e-4 Torr (as indicated above)

Increase ramping rate to 0.2A/min.

 Thursday, July 19, 2018, 12:12

Completion of the U-carbonization has been reached. 

Cooling down TGHT at 2A/min

Chamber will be vented in Ar and materials will be transferred to Ar glovebox