Thursday, September 23, 2021, 06:55

A loaded graphite cartridge was set in a tantalum boated and wrapped with 3 tantalum sheets (Wednesday September 22)

IGP1 = 3.6 e-5 Torr

Good vacuum = 5e-2 Torr

Bad vacuum = 5e-1 Torr

Current ramp is 2A per min from 0A to 120A and 1A/10s from 120A to (450-550A)

Thursday, September 23, 2021, 07:09 

IGP1 = 1.84 e-06 Torr

Start Autoramp to 120A @ 2A/min 

Thursday, September 23, 2021, 10:25

Start Autoramp to 550A @ 1A/10s

 IGP1= 1.05e-05 Torr

TGHT= 120 A, 1.06 V

Thursday, September 23, 2021, 11:57 

Pressure drop observed at 530A.  Start 4 hour count.  

Thursday, September 23, 2021, 15:57 

IGP1= 9.1e-06 Torr

After 4 hour reduction started rampdown to 400A at 2A/30s.

8 hour conditioning to start at 16:15 pm

Friday, September 24, 2021, 00:16

TGHT= 399.8 A, 3.5V

IGP1= 2.4 e-06 Torr 

Start ramp down at 2A/min

Wednesday, September 14, 2021, 21:14

Boat is wrapped with 2 layers of Ta-heat shield

The samples consists of 15 discs of UCx of 14mm diameter

The chamber is currently pumping down.

TGHT will be ramped up to 450 A

Wednesday, September 15, 2021, 07:17

IGP1 = 6.75e-6 Torr

Tapped up manually to 40A.

TGHT = 60 A, 2.39 V

Vacuum stable IG1 = 7.25e-6 Torr

Initiating auto-ramp for TGHT at a rate of 0.2A/min to 445 A

Parameter setup: 5.0e-5 good vac, 8.0e-5 bad vac.

 Wednesday, September 15, 2021, 11:57

IGP1=2.24e-5 Torr

TGHT= 102.016 A, 1.275 V

Autoramp changed to 1A/min to 450 A

Wednesday, September 15, 2021, 12:53

IGP1 = 3.3e-5 torr

TGHT= 150 A,  V

Autoramp changed to 2A/30s to 450 A

 1e-1 good vac, 5e-1 bad vac

Wednesday, September 15, 2021, 12:59

Friday, September 17, 2021, 07:54

IGP1 = 3.81e-6 Torr

TGHT = 449.6 A, 4.31 V

Autoramp set to -2A/min to 0 A 

 Wednesday, July 07, 2021, 14:39

Target Provisional ID = 200929 was installed in the EVAP1 and pumped down (Tuesday July 7, 2021).

Target is going to be thermally reduced for 8 hours and then conditioned for an additional 8 hours

IGP1 = 2.0 e-6 Torr

Good vacuum = 1e-1 Torr

Bad vacuum = 5e-1 Torr

Power desired 1.6kW.

10 extra discs included for analysis

Wednesday, July 07, 2021, 14:49 

Ramping up TGHT at 6A/min [wait interval = 10 s at increments of 1A]

Wednesday, July 07, 2021, 15:58

IGP1= 5.7 e-5 Torr and trending down.  Will start ramp up to 450A at  18A/min [wait interval 10s at 3A increments]

Wednesday, July 07, 2021, 16:20 

IGP1= 2.2e-3 Torr

Will continue ramping TGHT to 500A and watch pressure

Wednesday, July 07, 2021, 16:26

Continue ramping to 550 at 3A/10s

 Wednesday, July 07, 2021, 16:29

holding at 550A, 5.1V for 8 hours 

Wednesday, July 07, 2021, 23:41 

TGHT = 550A, 5.7 V

begin ramp down at -2A/min to 450A and leave for 8 hours

Thursday, July 08, 2021, 08:20

 IGP1= 2.7 e-06 Torr

TGHT = 450A, 4.5V

Will start ramp down at -2A/min to 0A 

Target #34 was installed in the EVAP1 and pumped down (Tuesday June 29, 2021).

Target #34 is going to be conditioned on a Ta boat wrapped with 3 Ta foils.

IGP1 = 1.85e-6 Torr

Good vacuum = 1e-1 Torr

Bad vacuum = 5e-1 Torr

Power desired 1.6kW. This is the second target conditioned this way. 

Subsequent targets should be conditioned following thermal reduction.

 Thursday, July 01, 2021, 06:05

IGP1= 1.35e-06 Torr

Start autoramp @2A/30s to 400A

Thursday, July 01, 2021, 07:59

Pressure increase was observed near 400A 

will ramp to 450A and  keep for 8 hours

IGP1= 1.4 e-05 Torr

450A and 4.0V reached at 8:14 am on Thursday July 01, 2021

Rampdown @-2A/min was started at 4.14 pm on Thursday July 01, 2021 IGP1 stable at 2.7e-06Torr

Cannot transfer into glovebox yet because moisture is a bit high after regeneration.  Moisture is dropping. Will wait until moisture is sufficiently low.

Monday, July 05, 2021, 20:43

Cartridge was removed and placed in bag inside glovebox

Removed 10 discs for analysis but might place them back inside depending on final decision.  We had previously removed 10 discs after thermal reduction.

 Saturday, June 05, 2021, 08:57

Target #33 was installed in the EVAP1 and pumped down yesterday (Friday 4).

Target #33 is going to be conditioned on a Ta boat wrapped with 3 Ta foils.

IGP1 = 3.85e-6 Torr

Good vacuum = 1e-1 Torr

Bad vacuum = 5e-1 Torr

Power desired 1.6kW. This is the first target conditioned this way, 

Saturday, June 05, 2021, 09:13

Current ramp is 2A/30s to 400 A

Saturday, June 05, 2021, 10:59

TGHT = 3.5V, 399.7 A, 1.4 kW

IGP1 = 4.4e-5 Torr

Saturday, June 05, 2021, 11:00  

Current ramp is 2A/30s to 450 A

Saturday, June 05, 2021, 11:14

 TGHT = 4.06 V, 451.584 A, 1.4 kW

IGP1 = 4.86e-5 Torr

Saturday, June 05, 2021, 11:15 

Current ramp is 2A/30s to 500 A

Saturday, June 05, 2021, 11:23

TGHT = 4.23 V, 467.2 A, 1.97 kW pressure was still increasing a little at 1.6kW

IGP1 = 4.86e-5 Torr

Saturday, June 05, 2021, 19:10

 TGHT = 4.08 V, 459.52 A, 

IGP1 = 6.4e-6 Torr

Initiate ramp down  at 2 A/min to 0A

Thursday, March 31, 2021, 14:42

EVAP1's TGHT has been tripping even when the pressure is below the tripping limits. The temperature of the turbo pump and the TGHT's power supply were monitored discarding the possibility of tripping due to the overheating of these pieces of equipment.

Gelo has been monitoring the IGP1 during carbothermal reductions to pinpoint the tripping issue, below is Gelo description to the issue and the patch he implemented to fix it.

"IGP loses its STATON (On status) if the value from the device is not within the valid voltage window (0.7 to 10 V). IEVAP:IGP1 for some reason goes to 0V for a few seconds then goes back up to where it left off.

Prior to the latest software updated, I added a 2 second delay in the code so that any invalid signal <=2s will be ignored.

Here is the data that you sent me specifically looking at when it tripped. I also attached the data that you sent me.  << File: 310321-P2N-3-CR (1).txt >>

TGHT Voltage and TGHT current are both read from the same PLC module, which tells me that the PLC module is not likely the issue since we were still reading other signals when IGP was reading 0.

For the new update, I adjusted the delay to 5 seconds since the signal drop seemed like it was about 2s and was enough to lose the IGP STATON bit which tripped TGHT.

The delay only applies for the STATON status which can also be described as reading OK status in this case. Any other trip will be instantaneous and work as normal. 

STATON is “ANDed” with other trips. i.e. IEVAPIGP_LESS10MTORR = IEVAPIGP1_RDVAC < 10mTorr AND IEVAPIGP1_STATON."

Green target material characteristics  (elog 105)

#discs = 49

Average disc thickness = 0.453mm

Empty cartridge weight = 9.42 g

Full cartridge weight = 39.86 g

UO2+C weight = 30.44 g 

Tuesday, March 30, 2021, 16:04

The target material was loaded in a P2N oven, wrapped with three heat shields, and set in the EVAP1

EVAP1 is currently being evacuated.

Wednesday, March 31, 2021, 09:42

IGP1 = 3.24e-6 Torr

Good vacuum 1e-1 Torr

Bad vacuum 5e-1 Torr

Autoramp set to 1A/10s to 150 A. 

Wednesday, March 31, 2021, 10:17

TGHT = .54 V, 149.88 A

IGP1 = 6.3e-4 Torr and increasing

Max pressure = 0.06 Torr

Wednesday, March 31, 2021, 10:33 

IGP1= 0.004 Torr

Autoramp set to 1A/10s to 200 A

Wednesday, March 31, 2021, 10:43

Maximum pressure 0.03 Torr and going down

Autoramp set to 1A/10s to 250 A

Wednesday, March 31, 2021, 11:04 

TGHT = 1.1 V, 299.9 A

IGP1 = 6e-4 Torr and going down

Autoramp set to 2.5 A/10 s to 700 A

Wednesday, March 31, 2021, 11:35

Ramp stopped at 690 A

TGHT = 2.9V, 689.1A

IGP1 = 0.127 Torr 

Wednesday, March 31, 2021, 11:37

Autoramp  set to 700 A at 1A/20s

Manually ramped to 740 A (3V) to make sure carbothermal reduction is done.

 Wednesday, March 31, 2021, 12:00

The power supply tripped, Gelo was monitoring the heating process.

Wednesday, March 31, 2021, 14:33

The target will be heated for 4 hours to get read of impurities.

IGP1 = 6e-6 Torr 

Autoramp set to 650 at 1A/10s 

Wednesday, March 31, 2021, 20:37

TGHT = 2.77 V, 669.6A 

IGP1 = 8.5e-6 Torr

EVAP1 ramped down to 0 A at 2 A/min

 Thursday, September 10, 2020, 14:01

A P2N target was carbothermal reduced but at the maximum current, the power supply tripped (elog. 267)

Therefore, the target was not hot long enough to fully outgas, that is why it will be reheated.

Desired current 650 A

Thursday, September 10, 2020, 14:07 

IGP1 =  3.3e-6 Torr

Autoramp set to 650 A at 1 A/10 s 

Thursday, September 10, 2020, 16:06

Ramp reached desired current

TGHT = 2.4 V, 649 A

IGP1 = 3e-3 Torr 

 Friday, September 11, 2020, 11:17

TGHT = 2.24 V, 649.2 A

IGP1 = 3.7e-6 Torr

Friday, September 11, 2020, 12:55 

 TGHT = 2.2 V, 648.8 A

IGP1 = 3.7e-6 Torr

Autoramp set to 700 A at 1 A/10 s,

No more gas was released, the system was ramped down to 0 A at 2 A/min

Friday, September 11, 2020, 18:17

TGHT = 0.35 V, 133 A

IGP1 = 2.7e-6 Torr

 Friday, September 11, 2020, 20:01

TGHT = 0 V, 2.56 A

IGP1 = 2.6e-6 Torr

Monday, September 14, 2020, 16:19

EVAP1 was vented with Ar and the P2N material was transferred to the preparatory glove box. 

 Tuesday, September 08, 2020, 20:44

A P2N oven with three heat shields, loaded with a graphite container filled with UO2/C ring-discs was set in the EVAP1

EVAP1 is currently being evacuated.

Wednesday, September 09, 2020, 10:11

IGP1 = 4.7e-6 Torr

Good vacuum 1e-1 Torr

Bad vacuum 5e-1 Torr

Autoramp set to 1A/10s to 150 A.

Wednesday, September 09, 2020, 10:50 

TGHT = .32 V, 149.8 A

IGP1 = 6.5e-5 Torr

Autoramp set to 1A/10s to 200 A 

Wednesday, September 09, 2020, 11:00

TGHT =0.46 V, 200 A

IGP1 =  6e-4 Torr and going up

good vacuum =  5e-2 Torr

bad vacuum = 1e-2 Torr

autoramp set to 1A/10s to 250 A

autoramp stopped at 215 A, since pressure kept increasing, the current was manually decreased to 180 A.

 Wednesday, September 09, 2020, 11:16

TGHT = 0.4 V, 179.7 A,

IGP1 = 8.5e-4 Torr an going down

good vacuum =  5e-2 Torr

bad vacuum = 1e-2 Torr

autoramp set to 1A/30s to 200 A

Wednesday, September 09, 2020, 11:32

TGHT = 0.46 V, 200.2 A,

IGP1 = 3e-3 Torr an going down

good vacuum =  5e-2 Torr

bad vacuum = 1e-2 Torr

autoramp set to 1A/30s to 300 A

Wednesday, September 09, 2020, 11:38

IGP1 = 1e-3 Torr 

Since the pressure was decreasing, the ramp was stopped at 210 and changed to  1A/10s to 300 A, vacuum limits remained the same

Wednesday, September 09, 2020, 11:53

The pressure reached the bad vacuum limit 1e-2 Torr and stopped

After ~8min the pressure limits were changed to:

good vacuum =  5e-2 Torr

bad vacuum = 1e-1 Torr

Wednesday, September 09, 2020, 12:05 

IGP1 = 1.15e-3 Torr

Autoramp set to 2.5 A/10 s to 700 A

Pressure increased! and ramp paused at 685 A

re-started autoramp to 700 A at 1A/10s

Wednesday, September 09, 2020, 13:56

Pressure kept increasing after 700 A, so autoramp was set to 750 A at  1A/10s

Pressure kept increasing

At 750 A pressure started reducing, autoramp was set to 760 A at 1A/10 s

System tripped suddenly (Gelo was notified)

The carbothermal reduction seemed complete 

Wednesday, August 19, 2020, 07:47 

XRD analysis of the P2N material showed that the carbothermal reduction was not completed

The material was loaded again in its oven, new Ta caps where secured to the edges, the body remained the same

The oven was set in the EVAP1 using Ar to avoid oxidation of the P2N material

See elog 263

Wednesday, August 19, 2020, 07:47

Good vacuum 1e-1 Torr

Bad vacuum 5e-1 Torr

IGP1 = 4.11e-6 Torr

Autoramp set to 1A/10s to 150 A.

Wednesday, August 19, 2020, 10:00

TGHT = .45 V, 149.8 A

IGP1 = 9.1e-5 Torr

 Autoramp set to 1A/10s to 200 A.

Wednesday, August 19, 2020, 10:13

TGHT = 0.6 V, 200.2 A

IGP1 = 3e-4 Torr and increasing

After 6 min:

good vacuum =  5e-2 Torr

bad vacuum = 1e-1 Torr

autoramp set to 1A/30s to 250 A

Since the pressure was decreasing, the ramp was changed to  1A/10s to 250 A, vacuum limits remained the same

Wednesday, August 19, 2020, 10:28

Good vacuum 1e-1 Torr

Bad vacuum 5e-1 Torr

IGP1 = 1.7e-4 Torr

TGHT =  0.78 V, 250.1 A

Autoramp set to 2.5 A/10 s to 700 A

Wednesday, August 19, 2020, 11:17

 Good vacuum 1e-1 Torr

Bad vacuum 5e-1 Torr

IGP1 = 2e-4 Torr

TGHT = 2.64 V, 699 A

Autoramp set to 2 A/10 s to 800 A

 Wednesday, August 19, 2020, 11:29

 Good vacuum 1e-1 Torr

Bad vacuum 5e-1 Torr

IGP1 = 5.2e-5 Torr

TGHT = 3.1 V, 798.8 A

Note: Voltage starts to become unstable, an power is around 2.3 kW, pressure has not increased enough to indicate reduction with certainty

In order to reach 3 kW autoramp set to 1A/10 s to 900 A

Wednesday, August 19, 2020, 12:18

The current was increased to 1000 A expecting to see a high peak in pressure but there was not an increase in preasure.

The target is being ramped down to 850 A 

Wednesday, January 29 2020, 05:55  

A P2N container  with heat shields, and with a UO2/C loaded graphite container was installed in the EVAP1

Chamber is currently being evacuated.

Thursday, January 30, 2020, 08:56

Pressure limits:

Good vacuum 1e-1 Torr

Bad vacuum 5e-1 Torr

Initial pressure: 

IGP1=1.52e-6Torr

Current ramp set to 1A/min to 10 A, voltage is stable.

Current ramp increased to 1A/10s to 100 A. The pressure started raising around 80 A.

Current was kept 5min at at 100 A, voltage was stable

Thursday, January 30, 2020, 09:32 

Current ramp set to 1A/20s to 150 A (same pressure limits)

Pressure keep increasing during heating

Thursday, January 30, 2020, 09:53 

Current was kept at 150 min during 5 min, the voltage is stable, pressure started to stabilize:

IGP1 = 0.027 Torr

TGHT = 0.418 V

Ramp set to 1A/min to 200 A.

Thursday, January 30, 2020, 10:02

Pressure decreasing:

TGHT= 153 A 

Marla Cervantes wrote:

Wednesday, January 29 2020, 05:55   A P2N container  with heat shields, and with a UO2/C loaded graphite container was installed in the EVAP1 Chamber is currently being evacuated. Thursday, January 30, 2020, 08:56 Pressure limits: Good vacuum 1e-1 Torr Bad vacuum 5e-1 Torr Initial pressure:  IGP1=1.52e-6Torr Current ramp set to 1A/min to 10 A, voltage is stable. Current ramp increased to 1A/10s to 100 A. The pressure started raising around 80 A. Current was kept 5min at at 100 A, voltage was stable Thursday, January 30, 2020, 09:32  Current ramp set to 1A/20s to 150 A (same pressure limits) Pressure keep increasing during heating Thursday, January 30, 2020, 09:53  Current was kept at 150 min during 5 min, the voltage is stable, pressure started to stabilize: IGP1 = 0.027 Torr TGHT = 0.418 V Ramp set to 1A/min to 200 A. Thursday, January 30, 2020, 10:02 Pressure decreasing: TGHT= 153 A

 Thursday, January 30, 2020, 10:15

At 155 A while pressure decreasing, the power supply tripped off,

Controls has been notified, waiting for instructions.

Marla Cervantes wrote:

Marla Cervantes wrote: Wednesday, January 29 2020, 05:55   A P2N container  with heat shields, and with a UO2/C loaded graphite container was installed in the EVAP1 Chamber is currently being evacuated. Thursday, January 30, 2020, 08:56 Pressure limits: Good vacuum 1e-1 Torr Bad vacuum 5e-1 Torr Initial pressure:  IGP1=1.52e-6Torr Current ramp set to 1A/min to 10 A, voltage is stable. Current ramp increased to 1A/10s to 100 A. The pressure started raising around 80 A. Current was kept 5min at at 100 A, voltage was stable Thursday, January 30, 2020, 09:32  Current ramp set to 1A/20s to 150 A (same pressure limits) Pressure keep increasing during heating Thursday, January 30, 2020, 09:53  Current was kept at 150 min during 5 min, the voltage is stable, pressure started to stabilize: IGP1 = 0.027 Torr TGHT = 0.418 V Ramp set to 1A/min to 200 A. Thursday, January 30, 2020, 10:02 Pressure decreasing: TGHT= 153 A   Thursday, January 30, 2020, 10:15 At 155 A while pressure decreasing, the power supply tripped off, Controls has been notified, waiting for instructions.

 Thursday, January 30, 2020, 11:51

Controls respond "It looks like the power supplies were tripped by either the pirani gauge (IEVAP:IGP1) or the Nuclear vent or by both. But, it did not look like that the interlock tree latched the bad condition when the power supplies tripped. I modified the PLC to properly latch the cause of the trip." and gave green light to restart the carbothermal reduction.

Marla Cervantes wrote:

Marla Cervantes wrote: Marla Cervantes wrote: Wednesday, January 29 2020, 05:55   A P2N container  with heat shields, and with a UO2/C loaded graphite container was installed in the EVAP1 Chamber is currently being evacuated. Thursday, January 30, 2020, 08:56 Pressure limits: Good vacuum 1e-1 Torr Bad vacuum 5e-1 Torr Initial pressure:  IGP1=1.52e-6Torr Current ramp set to 1A/min to 10 A, voltage is stable. Current ramp increased to 1A/10s to 100 A. The pressure started raising around 80 A. Current was kept 5min at at 100 A, voltage was stable Thursday, January 30, 2020, 09:32  Current ramp set to 1A/20s to 150 A (same pressure limits) Pressure keep increasing during heating Thursday, January 30, 2020, 09:53  Current was kept at 150 min during 5 min, the voltage is stable, pressure started to stabilize: IGP1 = 0.027 Torr TGHT = 0.418 V Ramp set to 1A/min to 200 A. Thursday, January 30, 2020, 10:02 Pressure decreasing: TGHT= 153 A   Thursday, January 30, 2020, 10:15 At 155 A while pressure decreasing, the power supply tripped off, Controls has been notified, waiting for instructions.    Thursday, January 30, 2020, 11:51 Controls respond "It looks like the power supplies were tripped by either the pirani gauge (IEVAP:IGP1) or the Nuclear vent or by both. But, it did not look like that the interlock tree latched the bad condition when the power supplies tripped. I modified the PLC to properly latch the cause of the trip." and gave green light to restart the carbothermal reduction.

 Thursday, January 30, 2020, 13:09

IGP1=5.9e-6Torr

Ramp set to 1A/10s to 200 A

Pressure rising too fast at 200 A, current reduced manually to 190 A

Pressure start dropping and system tripped, notify to controls again, "The strip tool shows the vacuum level shoot down to 0 then shoot back up for a quick second but that is enough to tell the PLC that IGP is “bad”"

Thursday, January 30, 2020, 15:58 

Restarting process to try to trip the system on purpose 

Initial pressure IGP1 = 2.7e-6Torr

Ramp set to 1/A/10s to 200 A, 0.59 V

Ramp set to 2A/10s to 300 A

Max pressure during process IGP1 = 0.03 Torr

Voltage increased and stabilized (see voltage rising).

Ramp kept at 2A/10s to 400 A

Thursday, January 30, 2020, 16:48 

TGHT = 1.54 V, 399.744 A

IGP1 = 0.00016 Torr and going down

Ramp set to 2A/10s to 500 A

Thursday, January 30, 2020, 17:02 

TGHT= 1.9V, 499.2 A

IGP1 = 0.00014 Torr

Ramp set to 2A/10s to 600 A

Ramp set to 0.5 A/min to 700 A, ramp stopped at 680 A

Manually tapped to 697 A

Pressure dropping indicated that carbothermal reduction is done.

Unfortunately, the system did not trip. 

Contact Gelo for the  next run, such that he can monitor the system and we can spot the problem.

Marla Cervantes wrote:

Marla Cervantes wrote: Marla Cervantes wrote: Marla Cervantes wrote: Wednesday, January 29 2020, 05:55   A P2N container  with heat shields, and with a UO2/C loaded graphite container was installed in the EVAP1 Chamber is currently being evacuated. Thursday, January 30, 2020, 08:56 Pressure limits: Good vacuum 1e-1 Torr Bad vacuum 5e-1 Torr Initial pressure:  IGP1=1.52e-6Torr Current ramp set to 1A/min to 10 A, voltage is stable. Current ramp increased to 1A/10s to 100 A. The pressure started raising around 80 A. Current was kept 5min at at 100 A, voltage was stable Thursday, January 30, 2020, 09:32  Current ramp set to 1A/20s to 150 A (same pressure limits) Pressure keep increasing during heating Thursday, January 30, 2020, 09:53  Current was kept at 150 min during 5 min, the voltage is stable, pressure started to stabilize: IGP1 = 0.027 Torr TGHT = 0.418 V Ramp set to 1A/min to 200 A. Thursday, January 30, 2020, 10:02 Pressure decreasing: TGHT= 153 A   Thursday, January 30, 2020, 10:15 At 155 A while pressure decreasing, the power supply tripped off, Controls has been notified, waiting for instructions.    Thursday, January 30, 2020, 11:51 Controls respond "It looks like the power supplies were tripped by either the pirani gauge (IEVAP:IGP1) or the Nuclear vent or by both. But, it did not look like that the interlock tree latched the bad condition when the power supplies tripped. I modified the PLC to properly latch the cause of the trip." and gave green light to restart the carbothermal reduction.  Thursday, January 30, 2020, 13:09 IGP1=5.9e-6Torr Ramp set to 1A/10s to 200 A Pressure rising too fast at 200 A, current reduced manually to 190 A Pressure start dropping and system tripped, notify to controls again, "The strip tool shows the vacuum level shoot down to 0 then shoot back up for a quick second but that is enough to tell the PLC that IGP is “bad”" Thursday, January 30, 2020, 15:58  Restarting process to try to trip the system on purpose  Initial pressure IGP1 = 2.7e-6Torr Ramp set to 1/A/10s to 200 A, 0.59 V Ramp set to 2A/10s to 300 A Max pressure during process IGP1 = 0.03 Torr Voltage increased and stabilized (see voltage rising). Ramp kept at 2A/10s to 400 A Thursday, January 30, 2020, 16:48  TGHT = 1.54 V, 399.744 A IGP1 = 0.00016 Torr and going down Ramp set to 2A/10s to 500 A Thursday, January 30, 2020, 17:02  TGHT= 1.9V, 499.2 A IGP1 = 0.00014 Torr Ramp set to 2A/10s to 600 A Ramp set to 0.5 A/min to 700 A, ramp stopped at 680 A Manually tapped to 697 A Pressure dropping indicated that carbothermal reduction is done. Unfortunately, the system did not trip.  Contact Gelo for the  next run, such that he can monitor the system and we can spot the problem.

 Friday, January 31, 2020, 15:35

The EVP1 was vent with Ar and the P2N target was transferred to the glove box.

Marla Cervantes wrote:

Marla Cervantes wrote: Marla Cervantes wrote: Marla Cervantes wrote: Marla Cervantes wrote: Wednesday, January 29 2020, 05:55   A P2N container  with heat shields, and with a UO2/C loaded graphite container was installed in the EVAP1 Chamber is currently being evacuated. Thursday, January 30, 2020, 08:56 Pressure limits: Good vacuum 1e-1 Torr Bad vacuum 5e-1 Torr Initial pressure:  IGP1=1.52e-6Torr Current ramp set to 1A/min to 10 A, voltage is stable. Current ramp increased to 1A/10s to 100 A. The pressure started raising around 80 A. Current was kept 5min at at 100 A, voltage was stable Thursday, January 30, 2020, 09:32  Current ramp set to 1A/20s to 150 A (same pressure limits) Pressure keep increasing during heating Thursday, January 30, 2020, 09:53  Current was kept at 150 min during 5 min, the voltage is stable, pressure started to stabilize: IGP1 = 0.027 Torr TGHT = 0.418 V Ramp set to 1A/min to 200 A. Thursday, January 30, 2020, 10:02 Pressure decreasing: TGHT= 153 A   Thursday, January 30, 2020, 10:15 At 155 A while pressure decreasing, the power supply tripped off, Controls has been notified, waiting for instructions.    Thursday, January 30, 2020, 11:51 Controls respond "It looks like the power supplies were tripped by either the pirani gauge (IEVAP:IGP1) or the Nuclear vent or by both. But, it did not look like that the interlock tree latched the bad condition when the power supplies tripped. I modified the PLC to properly latch the cause of the trip." and gave green light to restart the carbothermal reduction.  Thursday, January 30, 2020, 13:09 IGP1=5.9e-6Torr Ramp set to 1A/10s to 200 A Pressure rising too fast at 200 A, current reduced manually to 190 A Pressure start dropping and system tripped, notify to controls again, "The strip tool shows the vacuum level shoot down to 0 then shoot back up for a quick second but that is enough to tell the PLC that IGP is “bad”" Thursday, January 30, 2020, 15:58  Restarting process to try to trip the system on purpose  Initial pressure IGP1 = 2.7e-6Torr Ramp set to 1/A/10s to 200 A, 0.59 V Ramp set to 2A/10s to 300 A Max pressure during process IGP1 = 0.03 Torr Voltage increased and stabilized (see voltage rising). Ramp kept at 2A/10s to 400 A Thursday, January 30, 2020, 16:48  TGHT = 1.54 V, 399.744 A IGP1 = 0.00016 Torr and going down Ramp set to 2A/10s to 500 A Thursday, January 30, 2020, 17:02  TGHT= 1.9V, 499.2 A IGP1 = 0.00014 Torr Ramp set to 2A/10s to 600 A Ramp set to 0.5 A/min to 700 A, ramp stopped at 680 A Manually tapped to 697 A Pressure dropping indicated that carbothermal reduction is done. Unfortunately, the system did not trip.  Contact Gelo for the  next run, such that he can monitor the system and we can spot the problem.  Friday, January 31, 2020, 15:35 The EVP1 was vent with Ar and the P2N target was transferred to the glove box.

 Thursday, August 13, 2020, 14:33

XRD analysis of the P2N material showed that the carbothermal reduction was not completed

The material was loaded again in its oven, new Ta caps where secured to the edges, the body remained the same

The oven was set in the EVAP1 using Ar to avoid oxidation of the P2N material

Currently pumping down.

 Saturday, August 15, 2020, 14:45 

Vacuum is having a strange behavior, pressure shows that is going from 8e-11 to 4e-6 Torr (fig. 200815-Vaccum_P2N)

Proceeded to turn off turbo pump

Tuesday, August 18, 2020, 10:38

The IGP1 head was replaced with the EVAP1's IGP1 head

The vacuum will be started again

Marla Cervantes wrote:

Marla Cervantes wrote: Marla Cervantes wrote: Marla Cervantes wrote: Marla Cervantes wrote: Marla Cervantes wrote: Wednesday, January 29 2020, 05:55   A P2N container  with heat shields, and with a UO2/C loaded graphite container was installed in the EVAP1 Chamber is currently being evacuated. Thursday, January 30, 2020, 08:56 Pressure limits: Good vacuum 1e-1 Torr Bad vacuum 5e-1 Torr Initial pressure:  IGP1=1.52e-6Torr Current ramp set to 1A/min to 10 A, voltage is stable. Current ramp increased to 1A/10s to 100 A. The pressure started raising around 80 A. Current was kept 5min at at 100 A, voltage was stable Thursday, January 30, 2020, 09:32  Current ramp set to 1A/20s to 150 A (same pressure limits) Pressure keep increasing during heating Thursday, January 30, 2020, 09:53  Current was kept at 150 min during 5 min, the voltage is stable, pressure started to stabilize: IGP1 = 0.027 Torr TGHT = 0.418 V Ramp set to 1A/min to 200 A. Thursday, January 30, 2020, 10:02 Pressure decreasing: TGHT= 153 A   Thursday, January 30, 2020, 10:15 At 155 A while pressure decreasing, the power supply tripped off, Controls has been notified, waiting for instructions.    Thursday, January 30, 2020, 11:51 Controls respond "It looks like the power supplies were tripped by either the pirani gauge (IEVAP:IGP1) or the Nuclear vent or by both. But, it did not look like that the interlock tree latched the bad condition when the power supplies tripped. I modified the PLC to properly latch the cause of the trip." and gave green light to restart the carbothermal reduction.  Thursday, January 30, 2020, 13:09 IGP1=5.9e-6Torr Ramp set to 1A/10s to 200 A Pressure rising too fast at 200 A, current reduced manually to 190 A Pressure start dropping and system tripped, notify to controls again, "The strip tool shows the vacuum level shoot down to 0 then shoot back up for a quick second but that is enough to tell the PLC that IGP is “bad”" Thursday, January 30, 2020, 15:58  Restarting process to try to trip the system on purpose  Initial pressure IGP1 = 2.7e-6Torr Ramp set to 1/A/10s to 200 A, 0.59 V Ramp set to 2A/10s to 300 A Max pressure during process IGP1 = 0.03 Torr Voltage increased and stabilized (see voltage rising). Ramp kept at 2A/10s to 400 A Thursday, January 30, 2020, 16:48  TGHT = 1.54 V, 399.744 A IGP1 = 0.00016 Torr and going down Ramp set to 2A/10s to 500 A Thursday, January 30, 2020, 17:02  TGHT= 1.9V, 499.2 A IGP1 = 0.00014 Torr Ramp set to 2A/10s to 600 A Ramp set to 0.5 A/min to 700 A, ramp stopped at 680 A Manually tapped to 697 A Pressure dropping indicated that carbothermal reduction is done. Unfortunately, the system did not trip.  Contact Gelo for the  next run, such that he can monitor the system and we can spot the problem.  Friday, January 31, 2020, 15:35 The EVP1 was vent with Ar and the P2N target was transferred to the glove box.  Thursday, August 13, 2020, 14:33 XRD analysis of the P2N material showed that the carbothermal reduction was not completed The material was loaded again in its oven, new Ta caps where secured to the edges, the body remained the same The oven was set in the EVAP1 using Ar to avoid oxidation of the P2N material Currently pumping down.  Saturday, August 15, 2020, 14:45  Vacuum is having a strange behavior, pressure shows that is going from 8e-11 to 4e-6 Torr (fig. 200815-Vaccum_P2N) Proceeded to turn off turbo pump Tuesday, August 18, 2020, 10:38 The IGP1 head was replaced with the EVAP1's IGP1 head The vacuum will be started again

 Tuesday, August 18, 2020, 20:44

The pressure reading are normal after swapping the IGP1's gauge head

 INIFICON -  BPG - SN: 232

PN: 353-573

Tuesday, August 18, 2020, 10:38: Control head for IGP1 swapped with bagged one.

Had been roughing.

Tuesday, August 18, 2020, 12:37: Turbo pump on. 

Tuesday, August 18, 2020, 12:54: Vacuum @ 1.28e-05T & dropping. 

Wednesday, June 03, 2020, 08:11 

A loaded graphite cartridge was set in a tantalum boated and wrapped with 3 tantalum sheets (Friday May 29, 2020)

The set up was installed in the EVAP1 then IEVAP:IGP1 was replaced (elogs 260 and 261).  

Vacuum was turned on after Ion Gauge swap.

IGP1 = 3.6 e-5 Torr

Good vacuum = 5e-2 Torr

Bad vacuum = 5e-1 Torr

Current ramp is 1A per 10s from 0A to 120A

Wednesday, June 03, 2020, 09:59 

After about 20 minutes at 120 A, TGHT tripped again exactly as before.

Will restart ramp at 1A per 10s from 0A to 120A .  Will set good vacuum to 1e-2 Torr

IGP1= 4.3e-05 Torr

Wednesday, June 03, 2020, 10:57

IGP1 =  9e-4 Torr

Pressure peaked around 4e-3 Torr and now trending down

TGHT =120 A

Wednesday, June 03, 2020, 11:23

IGP1=9.5e-5 Torr

Good Vacuum 1e-02 Torr

Bad Vacuum 5e-1 Torr

Starting TGHT ramp to 550 A at 3A per 10s  

Wednesday, June 03, 2020, 14:41

ramp up was good.  TGHT at 550 A since 12:30 pm.  TGHT did not trip. *note adjusted good vacuum.  Ramping takes a little longer but doesn't trigger TGHT shutdown.

Wednesday, June 03, 2020, 22:55

IGP1 =  3.5e-5 Torr

TGHT = 249.4 A, 5.7 V

Start ramp down at -2A per minute to 0 A

 Replacement of electronic / controller head from INIFICON - BPG to Agilent - Model: FRG-730 due to EVAP 1 trips.

Monday, June 01, 2020, 09:37: Swap complete. 

 Replacement of electronic / controller head from INIFICON - BPG to Agilent - Model: FRG-730 due to EVAP 1 trips.

 Tuesday, May 26, 2019, 18:20

A loaded graphite cartridge was set in a tantalum boated and wrapped with 3 tantalum sheets (Friday May 22, 2020)

The set up was installed in the EVAP1 and pumped down during the weekend.

IGP1 = 7.10 e-7 Torr

Good vacuum = 1e-1 Torr

Bad vacuum = 5e-1 Torr

Current ramp is 1A per 10s from 0A to 120A

Tuesday, January 28, 2020, 10:11

A P2N container  with heat shields, and without graphite container was installed in the EVAP1

Chamber is currently being evacuated.

Wednesday, January 29, 2020, 10:12

Pressure IGP1=1.87e-6 Torr

Final desired current TGHT = 600 A

Manually tapped to 40 A.

Voltage increased accordingly in an stable way.

Wednesday, January 29, 2020, 10:33 

Autoramp is set to 3/30s to 300 A 

The voltage and vacuum were stable so the autoramp was kept at 4/30s and the final current was set to 600 A

Accidentally went up to 600 A (1.98 V)!

When updating autoramp to 600 A, did not realize that procedure status was Active.

NOTE: If the procedure status is "active" the heater autoramp, does not "ramp" the current input in "final value", it will go in one step to that current.

The current was manually ramp down to 300 A

TGHT=299.52A, 0.89 V

Wednesday, January 29, 2020, 13:25

After approximately 2 hours conditions IGP1=1.6e-6Torr, TGHT =300 A, 1V.

The current ramp was started again: 4A/30s  to final value of 600 A

 Wednesday, January 29, 2020, 14:07

After 15 min, TGHT=599.424A, and 1.983 V (unstable) (see figure "P2N-test2_final voltage")

The current was ramp down to 0 A  at -5A/20s 

EVAP1 was vented with aair and the container was removed,

the copper shims and legs did not present signs of damage

the body's tantalum sheet had wrinkles inside,

the tantalum foils unfasten a bit, but were adjusted.

Wednesday, January 22, 2020, 18:07

A P2N container  with no heat shields, and no graphite container was installed in the EVAP1

Chamber is currently being evacuated.

 Thursday, January 23, 2020, 09:45

Pressure IGP1=1.87e-6 Torr

Final desired current TGHT = 600 A

Manually tapped to 40 A

 The voltage looks ok, at 32 A the voltage's behavior change (see picture "voltage at 32 A") but is stable

Thursday, January 23, 2020, 13:20

Autoramp is set to 4/30s to 300 A 

The voltage and vacuum were stable so the autoramp was kept at 4/30s and the final current was set to 600 A

At 600 A the voltage was 2.4 V, the current and voltage remained stable for 1 hour (see figures 600A and 600A-zoomed)

Thursday, January 23, 2020, 15:57

The current was ramp down to 0 A  at -5A/20s 

Thursday, January 23, 2020, 16:36 

After 10 min at 0A, the current was ramp up to 600 A at 4A/30s.

At 600 A the voltage was 2.43 V (TGHT)

The container was left at 600 A overnight.

Friday, January 24, 2020, 10:51

The PN2 stayed at 600 A for 15 hrs

The voltage increased 0.1 V during the first 7hr at 600 A and then it stabilized at 2.5 V (see figure "second ramp voltage")

Friday, January 24, 2020, 10:57

The current was ramp down to 0A at -5A/20s  

 Tuesday, November 05, 2019, 16:43

A TaC coated target container  was loaded with a graphite cartridge with UCx

The target container has 3 heat shields

EVAP1 pumping down

Wednesday, November 06, 2019, 11:46 

IGP1 = 2.09e-6 Torr

Good vacuum 5e-5 Torr

Bad vacuum 8e-5 Torr

Autoramp set up to:

TGHT= 1 A/min to 465 A (same current used to reach 1865 C in evap2 when sintering TaC coating - e-log 464 evap2)

TBHT= 1 A/min 230 A

 Thursday, November 07, 2019, 10:15

After approximately 4 hours at maximum temperature the pressure was 5.85e-6 Torr and the autoramp was set to:

TGHT -1 A/min

TBHT -0.5 A/min

After 4 hours that the current stayed at 0 A, EVAP1 was vented with argon and the target was removed; before transferring the target to the preparatory glove box, the tantalum cap to collect deposits from the target was inspected, there was not deposits on it so it was determined that the conditioning was successful and the target was transferred to the preparatory glove box.

 One of the TBHT bolts  fell out of reach and may be sitting on the isolation valve or TP.

Remove TP as per WP:  I2019-11-05-9

Tuesday, November 05, 2019, 14:48: Completed. Found 2 TBHT bolts, a broken insulator, one small vented screw, and a piece of rubber.

Turbo pump mesh clear. Magnetic grabbing tool left in Evap 1 to potentially pickup /  grab materials before they fall down the hole if needed. The tip of the tool is contaminated.

Tuesday, November 05, 2019, 15:03: Evap 1 pumped down. TP1 started, IV1 opened. Ok.