Anders Mjos wrote:

See attached pdf and DocuShare for more photos. It may be possible to clean some of it from the Ground Electrode.

 Chad cleaned the GND electrode yesterday June 26th - see attached PDF. Photos on DocuShare.

TM3 HS water line helium pressure test is done at CS. 70 psi helium , 3 minutes.Base LR 0.0xE-9 atm.cc/sec, base pressure 0.0xE-4 torr.  No response. The line is leak free.

TM#3 with SiC#30 has been moved from the south hot cell to the conditioning station.

Electrical check of the TM#3 with SiC#30 attached. Also an electrical check of TM#3 after the cleaning of ground electrode with no target attached.

Chad and I leak checked the TM3 HS water line with new target installed.  No leak has been found during the check. Leak detector base LR 0.0xE-9 atm.cc/sec, base pressure 0.0xE-4 torr. The line will be helium pressurized at CS later.

Electrical check of TM#3 after the insulator repair. See attached PDF for details.

 See attached PDF. The object is not accessible with only the front panel removed. Photos on DocuShare.

Anders Mjos wrote:

When the Containment Box was opened today by Chad for a target change, we found the conductor insulator block B (ITD0054) to be broken close to the right TGHT terminal. Chad was nevertheless able to remove the target. See DocuShare and attached file for photos. An attempt to replace the insulator will be made tomorrow with a spare. A small sticky piece, likely off plastic material, was found next to the left main source tray insulator. The piece was removed from the Containment Box. See link above and attachment for photos.

 The two insulators ITD0053 and ITD0054 was replaced this morning by Chad. Photos on DocuShare. All bolts torqued with torque wrench see attached PDF for values.

See attached pdf and DocuShare for more photos. It may be possible to clean some of it from the Ground Electrode.

When the Containment Box was opened today by Chad for a target change, we found the conductor insulator block B (ITD0054) to be broken close to the right TGHT terminal. Chad was nevertheless able to remove the target. See DocuShare and attached file for photos.

An attempt to replace the insulator will be made tomorrow with a spare.

A small sticky piece, likely off plastic material, was found next to the left main source tray insulator. The piece was removed from the Containment Box. See link above and attachment for photos.

Electrical check of the TiC#4 on TM#3 post beam at the south hot cell, see attached PDF for details

Five F - 308 flasks containing five ISAC spent targets were moved from the anteroom into the south hot cell area. When the F - 308's were in the south hot cell area the rest of the bolts were installed on all the top covers. All the bolts were torqued and all the cable locks were also installed. All F - 308's  were then moved into the Active Services Area.

TM#4 with TiC#4 has been moved from the east target station to the south hot cell.

5 shielding blocks have been transferred from ITE to ITW. ITW is configured to take proton beam. Argon venting system for ITW is ready also.

Coil not used on TM1. Data and plots on DocuShare

Friday, June 13, 2014, 10:30. ITE receving p+

 Monday, June 16, 2014, 09:30: p+ off for maintenance day

 Thursday, June 19, 2014, 16:14: 10 uA p+ on ITW

Tuesday, July 08, 2014, 10:32:

Data uploaded to DocuShare

Five targets have been moved from the spent target storage to the mini storage. The targets that were moved are UCx #'s 6,7,8 , SiC #28, and Nb #6.

TM1 has been connected to ITW. It is pumping down in ITW with 6 turbo-pumps on.

TM#1 with UC#9 moved from the conditioning station to west station.

TM1 will be moved to ITW this morning.

The CS and TM1 is still under vacuum. They will be vented with argon tomorrow mornig