continue target heating up to 580 A. Strip tool for the heating up to 300A from yesyerday see below

heaters have reached final values TGHT 580 A, TBHT 230 A, some sparking during ramp up. see strip tool image attached

TPS:Q2 and TMS:MB1 failed during the scan. -> restarted.

mass scan crashed due to a network error will be restarted tomorrow

mass scan started again. Total current 3.2e-8 A

mass scan is finished and saved see attached.

Fc0 23 nA

IG1 9.9e-7 T

start automatic heater ramping down

heaters and HV power supplies have been switched off

IG1 5.1e-9 T.

The backing pressure at TSGRP1 does not go below 578 mT. Fault report to vacuum.

turbopumps in mass separator section started after power outages

Wednesday, April 18, 2012, 12:15: Blanked off cooling lines. Chamber ready to be pumped down.

Wednesday, April 18, 2012, 12:16: TSGRP1 makes unusual noise when attempting to pump down vacuum chamber. Roughing aborted for now. Edi Dalla Valle is informed. He will have a look at it after lunch.

Wednesday, April 18, 2012, 13:08 Anders Mjos wrote:

Wednesday, April 18, 2012, 12:15: Blanked off cooling lines. Chamber ready to be pumped down. Wednesday, April 18, 2012, 12:16: TSGRP1 makes unusual noise when attempting to pump down vacuum chamber. Roughing aborted for now. Edi Dalla Valle is informed. He will have a look at it after lunch.

 Wednesday, April 18, 2012, 13:08: Started pumping down again with Edi present. No noise was observed.

Wednesday, April 18, 2012, 13:10: Roughing the vacuum chamber.

Wednesday, April 18, 2012, 13:34 : Turbo pumps started and at speed. Pressure 3.5 E-5 torr

Friedhelm Ames wrote:

connected A(CH3)3 instead of He, pumped line and valve with pump on the high voltage rack.. Opened regulating valve first response at mass 27 with valve set point at 7.0.

 The bottle with Al(CH3)3 was removed from the test stand yesterday April 25.

comments in e-mail from Marik:

Anders & I took the Al(CH3)3 bottle out of the test stand & put it in the middle fume hood of lab 07.  There was some puffs of white "smoke" when Anders unscrewed the VCR coupling.  Likely some trapped liquid that oxidized on air exposure.  If at all possible, I would suggest a vertical orientation in the Faraday cage.

-Marik 

 TSGIG1 has timed out. As seen on the attached screen shot, the IG has been out since 17h May 1st.

Anders Mjos wrote:

TSGIG1 has timed out. As seen on the attached screen shot, the IG has been out since 17h May 1st.

 Wednesday, May 09, 2012, 09:15: ISAC Fault Report submitted

Anders Mjos wrote:

Anders Mjos wrote:  TSGIG1 has timed out. As seen on the attached screen shot, the IG has been out since 17h May 1st.  Wednesday, May 09, 2012, 09:15: ISAC Fault Report submitted

 Thursday, May 10, 2012, 08:12: Venting vacuum chamber for Edi - to repair the Ion Gauge.

Thursday, May 10, 2012, 08:45: Vented.

Anders Mjos wrote:

Anders Mjos wrote: Anders Mjos wrote:  TSGIG1 has timed out. As seen on the attached screen shot, the IG has been out since 17h May 1st.  Wednesday, May 09, 2012, 09:15: ISAC Fault Report submitted  Thursday, May 10, 2012, 08:12: Venting vacuum chamber for Edi - to repair the Ion Gauge. Thursday, May 10, 2012, 08:45: Vented.

 Thursday, May 10, 2012, 09:38: Ion Gauge filament replaced by Edi.

Thursday, May 10, 2012, 09:48 : Pumping down.

Thursday, May 10, 2012, 10:17: Ion Gauge reading vacuum at 1.3 E-5 torr.

Did a local IOC reboot to cure to white-out. The test stand is now operational.